Jump to content
SAU Community

Recommended Posts

Did back to back dyno testing at Boostworx. Eflex made less power then normal 98. The liberty e85 made 15-20kw more. Eflex isn't e85 its e70-e85 as it says on the pump.

While I dont doubt your figures this is totally the opposite of the testing I have carried out for our own vehicles.

However I have never tested 'Liberty' E85 only the United CSR Sarina manufactured blend, I think you may be getting confused with United. If there is a Liberty selling here let me know and I will test it.

E-Flex is a much maligned fuel. As stated on the brochure on the Caltex servo counter this fuel WILL contain as little as E70 in some circumstances, and yes it has when I test it (71% concentration is the lowest measured directly). This gives the fuel an effective tuning RON (my calcs here, not measuring on an octane machine) of around 110 - 112 RON. It is also highly oxygenated which means that it is capable of delivering good combustion energy - significantly higher than that of E85. I do not know why Boostworx have found it makes less power than 98 octane fuel as on a typical 200rwkw turbocharged engine (on a Mainline dyno) we can normally extract in the order of 10% - 14% additional power and torque swapping from 98 to E-Flex. The tuning technique required does however require some thinking outside of the square with some engines.

Yes, my family hack is a Flex-Fuel setup EVO X, and yes it runs on either 98, or more preferably (as it makes a ton more power and costs $40 a week to run) E-Flex :)

CSR Sarina E85 is a little more pure for the racers measuring at around 88% Ethanol in most cases and can make a tad more power than E-Flex (not a great deal in it). We run the United CSR blend in - all - our Willall Racing track and drag cars, but maybe we are missing something? :pirate:

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5936774
Share on other sites

Yup, I meant United not liberty on Tapleys Hill Rd >_<

Not to sure whay exactly it made less power then 98, wasn't by much though 230rwkw vs 226rwkw. Could have been a bad batch of fuel or it could have been down to tuning technique.

But as I said, and you stated above. The United E85 will make more power then eflex as its a more pure blend. Considering the United E85 is as cheap as eflex I know what i'll be buying all day every day.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937061
Share on other sites

Cheers guys.

Considering runnoing the evo on it.

A few blokes from other states have been doing it for awhile.

Have seen back to back dyno results and have been impressed...

As far as 'stuffing things up' i havent heard of much. what are the risks?

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937191
Share on other sites

Here, here, good to see your still a champion for the good stuff Mr Donnon.

I say go for it, Eflex is more than capable even at 70%.

I use the United E85, but have no problems at all throwing in Eflex,

United's wins on my seat of the paints dyno.

Recently tuned a S15 SR to 1.85bar on E85 running a disco with all the bolt on's, got a good compromise mapping both fuels, hasnt had it's power measured yet, but far out it fly's, high 200's at a guess.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937549
Share on other sites

Here, here, good to see your still a champion for the good stuff Mr Donnon.

I say go for it, Eflex is more than capable even at 70%.

I use the United E85, but have no problems at all throwing in Eflex,

United's wins on my seat of the paints dyno.

Recently tuned a S15 SR to 1.85bar on E85 running a disco with all the bolt on's, got a good compromise mapping both fuels, hasnt had it's power measured yet, but far out it fly's, high 200's at a guess.

.82 rear or .64? I've got the .64 making 240rwkw at 20psi dropping off to 16psi (small wastegate). If you have .82 is there much lag? would be keen to see power graphs as thinking of changing rear housings on mine.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937604
Share on other sites

I'm amazed at the attitude towards E70 vs E85............I think peeps are forgetting that the fuel alone won't give you the kind of power you're looking for.

In fact, 98 pump fuel will burn much better (combust) than the higher octane Ethanol.........the stuff just doesn't burn!!!

What the Ethanol allows you to do is turn up the boost and and throw more ignition timing at it, hence where the additional power comes from................the stuff doesn't know the meaning of the word Detonation!!!

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5938071
Share on other sites

people still hate on e85 haha, i have been running e85 for 3 years thanks to adrian, never had a issue pushing awesome power! it really is power for nothing compared to what some people spend chasing small gains, as well as safer. as for blends tryed nearly all varietys and never had issues.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5938162
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...