Jump to content
SAU Community

Jjr Short Shifters

luvpsi
 Share

Recommended Posts

89CAL Grand Master

89CAL

Posted
Posted

make your own. Thats what I did.

pulled the outer metal section of the shifter off (its seperated from the centre part by rubber) and cut the thread from the outer section and welded it onto the inner section. Solid short shifter, Cost = $0

Replaced bush that sits on the bottom as well. Next to no slop now and feels alot nicer.

If you have access to some tools + a welder then its a cheap option if you really want to do it. I had a spare one lying around so I just thought I'd give it a go.

SargeRX8 Grand Master

SargeRX8

Posted
Posted

I have a short shifter on my R33. From what I recall it doesn't even have circlips... It is just the shifter and a series of bushes then a clamp to hold it all in place. The shift and gear control was awesome. The sound of a solid shifter shit me up the wall. The whirring noise that the shifter throws up is terrible. The Nismo shifters have a shorter throw than stock and do not let this noise through. Any solid shifter is going to let noise through, both skylines Ive had(R33's) used the same shifter and had the same noise. No matter how much rubber shit I put around it. Ive tried a plastic, stock and metal gear knob. Metal was the worst the stock one helps get rid of it and the other drift one didn't really do anything.

http://www.ebay.com.au/itm/Nissan-Skyline-Short-Shifter-Kit-R32-R33-/320741118270?pt=AU_Car_Parts_Accessories&hash=item4aada9113e

Mine looks like this. Pretty much exactly the same. Only reason I don't use it anymore is because my current stock shifter feels fine enough and not worth the extra noise you get from these shifters. BELIEVE ME you WILL notice it. Unless you're deaf or have your music always on, its audible. My car isn't quiet either.

SargeRX8 Grand Master

SargeRX8

Posted
Posted

Ive got 3 layers. One from my old car, the current and one wrapped around the base. Still was shit lol. Its the vibration and noise which travels through the stick which is shit. They should be dampened inside but that would defeat the point of a solid shifter...

89CAL Grand Master

89CAL

Posted
Posted

Hmmm I've never really noticed any extra noise. Its not rediculous anyway. If I had to say anything I'd say its a bit noisey under low revs high load (say in 4th gear at 30kmh) but other then that I dont find it to bad.

I got a brand new boot to go directly on the gearbox (as these always seem to be stuffed) and then ditched the lower portion of the rubber boot that sits in your car because my shifter was hitting it, I'm pretty sure I have an SR20 manual shifter but I'm not sure if its just that slight bit different or if somewhere during my modification I've bent it slightly. But anyway I'm happy with how it turned out :)

Tangles Grand Master

Tangles

Posted
Posted

thats the one Ive bought for the R32-rb26, using VL turbo gearbox.

might try to install it tomorrow - havent worked on the car for a month so probably time to give installation a go

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I actually had my short shifter taken out all those years ago.

You tend to out shift the box too often due to the short through, which resulted in crunching the gearbox quite often.

Went back to stock and much less chance to out shift the synchros etc. Just something to think about.

I dont have a lot of mechanical sympathy :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...