Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

http://www.ebay.com....=item20bb013d31

i got it of a mate for a birthday gift, but they go for $150 as the link.

yeh i mounted it myself, just got some bendy mounting brackets from Bunnings and i was set. i installed jethros too.no more than half a litre at most.

Trans oil should have Thermostat,

as it runs hotter then Engine oils.

so its great putting bigger cooler on but trans runs at about 100 too 110 degs,

if you can find Mazada FD cooler it has built in thermostat ,you may want too look at Filter kits for trans as it will prolong trans oil life.

post-36964-0-75811100-1313646160_thumb.jpg,

http://www.summitrac...arts/DER-13090/

good luck,

if you can find Mazada FD cooler it has built in thermostat ,you may want too look at Filter kits for trans as it will prolong trans oil life.

post-36964-0-75811100-1313646160_thumb.jpg,

Chuckie this is exactly what I want. Can you still pick them up new from Mazda? Or do you need to find a second hand unit?

may be NEW but at WHAT COST HATE TO THINK pinch.gif

I got mine 2nd hand,both in good nick too,

i run one on Trans with Filter kit ,

one on Engine oil with remote + stock filter,

has made a big difference to oil colour as before it was not red as it should be,

iam about to do Trans oil sample so i shall post up what i find out,:thumbsup:

any filter will help oil life ,my steering cooler is a big winner as its red still ,before i would change oil in top tank every week & it would be Black.

I had the 6cyl version of the PWR trans cooler (like the one Aaron showed).

Mounted it as you can see below... until I upgraded the intercooler.

IMG_2130r.jpg

I reckon Chuckie's suggestion is pretty good although there have been no ill-effects with a large trans cooler on M35's.

Trans oil should have Thermostat,

as it runs hotter then Engine oils.

so its great putting bigger cooler on but trans runs at about 100 too 110 degs,

if you can find Mazada FD cooler it has built in thermostat ,you may want too look at Filter kits for trans as it will prolong trans oil life.

post-36964-0-75811100-1313646160_thumb.jpg,

http://www.summitrac...arts/DER-13090/

good luck,

best advice ever chuckie!

and idea on the physical size of that transmission cooler? it appears to have the right fittings etc to plumb it straight in

Been hanging to get mine up2 MVs.. Turbo tune said Its the biggest trans cooler they have seen .. "u could use it as a front mount" lol

Hada get it relocated when I put da FMIC on.. sits drivers side behind the body kit factory holes either side on stock S2 front bar bar.

Had shift problem b4 nistune and tune.. Better then all good now... But Really wnt MVs to have a look at the whole set up and find out what was done!

Cheapest I can find for an RX8 oil cooler - http://www.mazdatrix.com/getprice.asp?partnum=14-700D-N3H1

Thought I'd ask SK about his thoughts on it. His brief response was "There is no such thing as too cold transmission fluid."

I don't know what to believe/think. In Australia does it really get cold enough for this to be a concern?

Cheapest I can find for an RX8 oil cooler - http://www.mazdatrix...um=14-700D-N3H1

Thought I'd ask SK about his thoughts on it. His brief response was "There is no such thing as too cold transmission fluid."

I don't know what to believe/think. In Australia does it really get cold enough for this to be a concern?

given I can put my hand on mone and almost get a burn off it - yes it is needed and I do agree with teh above statement. heat kills these things - I have a $4500 bill to prove it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...