Jump to content
SAU Community

Recommended Posts

ok so the common problem people have with c34 stageas and turbo timers is when the lights are on auto and the turbo timer is on and u get out the lights dont turn off even when u open the door you must wait till the car shuts down then open and close the door very anoying.

The easiest fix is put a relay on the earth wire {black wire} to the auto lights module behind the instrument cluster and hook it up to the ignition so when the turbo timer shuts down the lights go out no matter what. i wired mine up that way 1 week ago and works great.

i even covered the sensor on the dash with a black sticker so the lights are always on when i am driving looks better and safer

parts needed 5 pin relay

female spade terminals and crimper

screwdriver

test light or multimeter

relay pin 30 cut earth wire from auto light module

pin 85 ignition

pin 86 earth

pin 87a other side of cut auto light wire

have fun

post-23888-0-71354100-1315553269_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/376688-c34-auto-lights/
Share on other sites

Yep the cluster needs to come out and the box is just behind it held with one screw I don't have a photo of the relay that I put in but just get a normal automotive change over relay and follow my instructions and u can't go wrong

Link to comment
https://www.sau.com.au/forums/topic/376688-c34-auto-lights/#findComment-6008640
Share on other sites

Weird I've never been in one with out it.... (Been in over 10)

Personally I wouldn't put tape over the light sensor on the dash either as this is also used by the climate control unit.

The sensor on the Passenger side is for the climate control, driver's side, auto lights.

Link to comment
https://www.sau.com.au/forums/topic/376688-c34-auto-lights/#findComment-6024977
Share on other sites

  • 2 weeks later...
  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...