Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

I've got my drum sitting on a few wood chocks just to keep it off the concrete...

In terms of pump, I use a jiggle siphon for about the first barrel as it's nice and easy. I also have a rotary barrel pump for the second half of the tank. It takes a little more time to attach but pumps really quick and easy. When I'm finished I always seal back up the drum :)

anyone using the macnaught rapidflo?

http://www.macnaught.com.au/shop/item/rapidflo

or the alemite version..

www.alemite-lubrequip.com.au/Portals/0/ServiceSheets/5080A.pdf

keen on one of these but $500 is a bit expensive for something i'll use once a month.

anyone know where to source these cheaper?

redistrip at blacktown....the guys at sucrogen asked them to sell the fuel cause they're close to EC and have the appropriate licences to store it.

they know very little about e85 or of any fuel transfer systems.

what's the transfer rate with the std pump? can't remember....been a while since i had a std pump.

Edited by tk80

PIGGAZ and I use a stock gtr fuel pump and a basic switch with alligator clips for power. Could be made to work from mains power with a bit of effort. Costs a lot less than $500

That's not a half bad idea haha

Might have to give that a go :)

I use an Alemite diesel rotary pump, but the ethanol dries out the gears so it can be difficult to prime. I open it up between each drum and re-lube the gear and race.

To refuel at events I use a cheap $30 go-kart battery pump from 20L drums. The 2 D cells last around a dozen or so 20L drums!

It's funny as shit to watch the pair of them stuffing around with a good 10 jerry cans @ any event, then their little motorised pump is lol :D

But it works. It's a damn good convo starter too!!

I'd say it empties a 20 litre can in 3 minutes ( I need to time it... I'll do that next time). Not the quickest way, but a shit load easier!

It's funny as shit to watch the pair of them stuffing around with a good 10 jerry cans @ any event, then their little motorised pump is lol :D

+1 Sounds like hard work. Conventional plastic jerry can with breather hole size bored out = quick dump of fuel into the tank with hardly any effort.

+1 Sounds like hard work. Conventional plastic jerry can with breather hole size bored out = quick dump of fuel into the tank with hardly any effort.

It's pretty handy when you want to throw 3 full jerries in, instead of standing there in the sun holding 20 kgs for minutes on end.

As long as ya keep the drums up off the ground i.e on a pallet or something similar they will last longer than it'll take you to burn it up lol.. Just make sure ya seal the drum after ya open it up as it will suck in the moisture.

  • 4 months later...

http://www.gettoolsdirect.com.au/fuel-transfer-equipment/macnaught-gp-rapid-flow-hand-pump.html

just used mine for the first time and couldn't be happier. expensive but does the job very quickly and very easily. emptied every last drop from drum without tilting also.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...