Jump to content
SAU Community

Recommended Posts

I have two bootlids, one is plain, the other has the std R34 GTR wing on it. I only did a 6-8 laps at Winton with the rear spoiler and I dont think it makes much of a difference. When I get a chance I want to throw the wings and boot lids on a trailer and test one day at Winton...since I am moving to within a 45min drive of Winton for a project there are going to be plenty of Friday practices that I run down for

Uhuh. I have two boots as well, one with replica 32 GTR wing and Nismo lip, other with ARC alloy wing with adjustable gurney flap. ARC defs creates more rear downforce, but unbalanced it front to rear (I don't have a front splitter).

Suprisingly, adding the Nismo lip to the stock GTR wing made a noticable difference. Evidently creates a high pressure zone atop the boot lid.

Well, I have a front undertray, though its not on the car at the moment as it makes a wheel alignment a pain and I need to get the car aligned and the oil cooler installed properly as the panel beater all that time ago didnt have the time to mount it properly. Also makes it a pain to get to the brake air guides etc which I can now finally finish because the Stoptechs are on and never coming off

So when the boot lid goes on I will have the undertray on

I have an undertray/skid plate, it made a small improvement but no match for "big wing like Mig fighter jet" (Russian accent)

I hope to get the mojo to make a front splitter extension about 4/5 inches to actually get some front downforce, rather than just trying to minimise lift.

you want voltex wing big boy. bit expensive but heaps good white man magic.

either that or use the C-West GT wing II - Suzuka like what I sold berry for his R34 (in it's V1 guise). they make R34 bolt on version and it works bloody well.

Thanks for the heads up.

It would be good if I could put a leading edge lip on the front of my undertray. Will e easy to do, only problem is I drive my car daily so god knows the Cossie is a nightmare being only 50mm off the ground...dont want the R32 to be the same so would have to be removable for daily driving duties....the ideal solution I have is too expensive so wont go there :)

if you've got two boot lids, so who cares how many holes there are in one of them?

I'm sure expensive Voltex wings are very good, but my $300 CF China wing worked well enough to totally transfom my car from near uncontrolable oversteer to plough understeerer in back to back sessions on the same day not touching anything else on the car. While only costing ~3kph in top speed, but that was into a headwind that day... And it dented the hatch in on my 180SX. I went 7 tenths quicker than before on those tyres, while being very compromised by understeer. If you could balance that out with front aero, you'd easily make at least that much time again. probably more. If a $3000 Voltex wing works better, its only going to make your life more difficult to get enough front aero.

The gurney flap would make a difference. But a dual plane wing is technically a better solution. You need one of these...but woudl cost waaaaay more

srcx_skyline_gtr-img600x450-1317020464ep9lwg21910.jpg

But, truth is I dont pretend to know that much about aero. To me its all wank for 99% of us. We end up with ugly cars with parachutes attached...but there are a few basic concepts that seem best to follow

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...