Jump to content
SAU Community

Recommended Posts

HI ALL I GOT A R32 GTR 1989. HAS A APEXI POWER FC Z32 MAFS, CAMS, COOLER, INJECTORS THE NOMRAL STUFF

JUST HAPPENED OUT OF NOWHERE WHEN TO DRIVE IT STARTED IT UP MOVED OUT OF DRIVEWAY WHENT TO TAKE OFF AND IT DIES IN THE ASS.

PUT IT IN THE GARAGE AND SAT THERE WILL REV BUT WITH HESITATING WHEN U PUT URE FOOT DOWN LIGHTLY AND HOLD IT THERE BUT WHEN U STAND ON IT IT JUST POPS AND FARTS AND BACKFIRES THROUGH THE INTAKE AND WONT GO OVER ABOOT 2-3,000

CHANGED FUEL PUMP AND HAS POWER AND ALL GOOD

CHANGED FUEL PUMP CONPUTER IN THE BOOT AND THE RELAY NOT THEM

MAFS ARE BOTH WORKING AS FAR AS A CAN SEE. TOOK TOPS OFF AND LOOK OK. BUT NOT 100% AS I HAVENT CHECKED THEM ON ANOTHER CAR OR VISEVERSA

NOT TOO SHURE ABOUT COMPUTER HAVENT GOT HAND CONTROLLER TO CHECK IT OR ANYTHING

INJECTORS AND COIL PACKS ARE GOOD.

CHANGED COILPACK WIRING NOT THAT.

CHANGED SPARK CONTROLER OR WHATEVER IT IS ON THE TOP OF THE COILPACK COVER NOT THAT

CHANGED EXHAUST CAM SENSOR NOT THAT

TURBOS ARE FINE.

PRETTY SHURE ALL THE HOSES AND ALL ARE STILL FINE.

HAS GOOD FUEL PRESSURE.

IT SEEMS TO REV A LIL BETTER WITH HIGHER FUEL PRESSURE BUT CANT FIND OUT WHY IT WOULD BE IT SITS AT AROUND WHAT IT SHOULD BE ACCORDING TO THE MANUAL MAYBE A LIL HIGHER.

IF ANYONE HAS ANY OTHER IDES OR CAN HELP ME OUT WITH MAYBE BORROWING A MAF SENSOR OR ANOTHER COMPUTER THAT HAS ABOUT THE SAME MODS SO I CAN DEFINATELY RULE THEM OUT THAT WOULD BE SUPER. AND COMPINSATED THROUGHT HE BEER ECCONOMY OF COURCE.

tested the volts on them and had mates computer in it with the hand controler and the volts when up on them but may still be the problem ill try get some known working ones to try

  • 3 weeks later...

all were wrong sort of.

found out by looking through the computer that all the settings for everything were set back to stock. computer has wiped and reset it self to the factory rb26 settings. so mafs were wrong injectors were at 100% and maps are wrong just needs a retune now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...