Jump to content
SAU Community

Recommended Posts

Hey guys, attached are some pics of my front driver side pads that came out of an S13 Silvia (CA18). I’ll detail the setup and my questions below.

PADS are QFM A1RM

Car has only 165rwkw and runs around 1:43 around Winton.

Runs Federal 595 RS-R Rubber (235 R17s)

Runs TRW Lucas 600 Fluid

Runs RDA Slotted/Ventilated Rotors up front, solid slotted rears

Runs S15 calipers up front, standard rear

Runs R32 GT-R Master Cylinder

Standard brake lines

Pads have done about 5 track days, 1 drift day, and 2 DECA days and very minimal street driving. All up under 2500ks total.

Why would only the inner driver side pad wear like this? The passenger side pads show wear similar to the outer pad from the driver side and appear to have some meat left. Rear pads are fine.

There’s clearly something amiss here to have that much difference in pad wear from the inner to outer pad, as well as such different pad wear side to side as the passenger side shows even wear inner to outer pad.

Thoughts?

post-23873-0-33870100-1317618020_thumb.jpgpost-23873-0-40618000-1317618043_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/378968-uneven-pad-wear/
Share on other sites

Firstly, you got MAX life out of them, they're rooted! lol

How are your wheel bearings? The hub moving under load in turn causes one pad to contact, causing wear.

Also, your calipers probably need a clean up and some new seals thrown through them, you could well have one piston thats a bit stickier than the other.

Link to comment
https://www.sau.com.au/forums/topic/378968-uneven-pad-wear/#findComment-6042573
Share on other sites

  • 4 weeks later...

Heat.

Turbo silvias have a big vent for the intercooler on the front left and no vent on the right so your right inner pad is probably getting hotter than the inner left.

The pad is still wearing fairly evenly though it's a bit hard to say for certain when they are that low because they tend to fall apart...

Link to comment
https://www.sau.com.au/forums/topic/378968-uneven-pad-wear/#findComment-6079600
Share on other sites

I've cut slots into the inner guard on the right side as well as I noticed that difference.

However the right side has my oil cooler so hot air could be flowing through. Might be worth making up some basic deflectors for the LCAs

Link to comment
https://www.sau.com.au/forums/topic/378968-uneven-pad-wear/#findComment-6079661
Share on other sites

  • 4 weeks later...

Further to this, pulled the rotors to have them machined. Noticed that the side that had worse pad wear also has noticable more rotor wear, to the point where the slots on the inner side of the rotor looked fairly wiped and may not come good with a machine.

Still sound like a heat issue? I couldn't detect any deflection in the wheel bearing but I note the tie rod ends dust boots are split.

Link to comment
https://www.sau.com.au/forums/topic/378968-uneven-pad-wear/#findComment-6129750
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...