Jump to content
SAU Community

Recommended Posts

Exhaust note sounds pretty tough in my opinion, especially when your right up it! We're just running off the spring pressures so far. Car has been de tuned to 350rwkw on 17psi

It's running the smaller .91 rear housing though it's probably a touch laggy but we will be playing with the cam gears and will hopefully be able to being it on 3-500 rpm earlier

I suppose I see it as a touch laggy as the only other high hp car I've driven at that level is Piggaz's 2.8 -5 setup on e85 and that things pretty responsive

But yea feul is just pump at the moment so will hopefully be cracking over 430rwkw with some boost and better fuel

Forgot to mention I'm also running the Ross crank trigger setup with a link g4 ecu and I have to say the car runs very well in terms of idle and light throttle applications

Edited by GTR_JOEY
  • Replies 105
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

The extra 200cc Piggaz' car has would make a big difference.

Sounds really promising so far man, I'd not be overly surprised if you got in the territory of your 430kw target at 25psi just on pump gas. Don't be shy on E85, lets see 500kw :D

Oh your poor gearbox Joey.

It's ok. We can have a 'gearbox BBQ' when it dies. Throw yours, mine and Steveo's gearset in a fire and watch them burn!

It's going to see what this thing makes on E85! It's going to be one wild ride :D

  • 1 month later...
  • 2 weeks later...

I purchased a 8375 FMW.. Won't make it into the car for a while though.. Need new ECU fuel system ect.

I was pretty disapointed with the casting quality of the housings though. Especially the exhaust housing.. its rough as inside..

Purchased from Street to Track.

I bought my last Garrett through him and he's very cheap, extremely fast and great to deal with..

Will get some pictures when I get some free time..

How much did it cost u? I've been trying to order one from himni racing but they only seem to reply to email every Saturday so waiting on an invoice

1400 seems a bit steep.. I got mine for 950 Inc V band + delivery from full race..

Personally I think the 83/75 will perform pretty well.. I havent wound full boost into mine yet but it's looking very promising. Looking to crack 450 on E85.

And they sound frigan awesome!

  • 3 weeks later...
  • 1 month later...

They really aren't very clear with the naming conventions, !!

S366SX is looking very probable for me, would love to see if there is something that sits exactly around 600hpatw though.

Well mine made 375rwkw on 18 pound, on 25 psi 450rwkw should be doable.. That's around 600hp

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...