Jump to content
SAU Community

Recommended Posts

Hoping someone can give me a bit of information here,

I recently brought an R33 gtst and the bloke i got it off said it had a highflowed turbo but thats all he knew about that. The impeller is aluminium and being a series 2 it should be nylon so this leads me to believe it probably has been highflowed.

My questions are is there any way to tell for sure it has been highflowed? How much boost is "safe" for a highflowed turbo? also where might it have been highflowed how many places actually do it ?

Oh and the car has 3' pipes from turbo back, Pod and a big FMIC

Edited by Slattery Gts-t
Link to comment
https://www.sau.com.au/forums/topic/379264-highflowed-turbo-help/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

The age old - How long is a piece of string?

There are 100s of places that could hi-flow a turbo, and to any specification.

If it's a hi-flow, it is very possible it wont even have an ID tag - or that it's even correct.

The only way to really know is the following:

1. Find out from previous owner who made it, and any reciept/info/specs

2. Pull the turbo off, measure both the front and rear wheels = 100% known specs.

Unless you do this all you can do is wind boost into it, tune accordingly, see what happens.

Ok took the turbo off today

It has an id tag from MTQ engine systems with a serial number and part number, also the impeller is 69MM across ( I took the impeller housing off to measure ), The inner diameter of the outlet tube is 52MM from memory

Also, the compressors or turbines arent made of nylon at all, ever, on any turbo.

actually 25neo turbos have nylon compressor wheels and ceramic exhaust wheels

nylon reduces the mass moment of inertia of the wheel = less lag

It's not a hair dryer, or a electric supercharger.

It's a turbo charger. They can reach speeds of up to 150,000 rpm,nare balanced to perfection, and have a lot of pressure applied to the compressor wheel due to physics.

Do you think something made of plastic or nylon would be able to withstand this?

Have the people crapping on about them being made of plastic even seen a real one?

I guess the pistons inside your engine need to be light, so let's just make them out of plastic too?

So you're just going from what the internet says, with nonform of confirmation, or have you actually touched one, and inspected one closely?

You obviously haven't. You also obviously don't realise how much stress a compressor wheel has to endure.

Mafia - they are really Nylon - i know it doesnt seem likely but I have swapped my stock turbo with another one plus seen a whole bunch of others at the wrecker first hand and in this case the internet is correct - take a look at one if you can and you will see that it is really some sort of black plastic.

I will have my turbo off in around 1 week and will happily post a photo of the compressor.

I'd take a chance with it then mate, if it's stamped and the diametres are bigger than factory. Other than that, get back onto the guy you bought it from and try and get some receipts or something.

Re: Nylon Compressor wheel. I have a R34 with a Neo RB25 in it. It has a stock turbo on the side. Said stock turbo has a nylon synthetic polymer compressor wheel. It's okay for your mind to be blown every once in a while mate. :thumbsup:

The funny thing about the limitations of the stock turbo though, is the ceramic turbine wheel is what fails first under heat load. Go go fantastic plastic! :D

So you're just going from what the internet says, with nonform of confirmation, or have you actually touched one, and inspected one closely?

You obviously haven't. You also obviously don't realise how much stress a compressor wheel has to endure.

The funny thing about the limitations of the stock turbo though, is the ceramic turbine wheel is what fails first under heat load. Go go fantastic plastic! :D

LMFAO.

Just when you think you knew it all...

FANTASTIC PLASTIC COMES TO COCK SLAP YOU IN THE FACE!!

Just a note, my series 2 rs4s turbo front wheel looks to be an metal looking compound where the chunks are missing, looks similar to cracked aluminum texture. I have it sitting on my bench without a front housing if someone wants a pic. It may be nylon, I'm not saying for sure what it is but to me personally it looks metalish.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...