Jump to content
SAU Community

Recommended Posts

Yeh Hambo it was the same reason I went to a 7. Look hard enough you will find a good cheap one especially that everything is interchangeable.

230kw aswell should be a safe comprimise too!

Alex, there is heeeeaapps of room in the evo I reckon it's a good family car. Had my parents in the back and they had heaps more room!

You have to check it out! I seriously think this is the best cars I've owned and everyone around me is agreeing

Yeh Hambo it was the same reason I went to a 7. Look hard enough you will find a good cheap one especially that everything is interchangeable.

230kw aswell should be a safe comprimise too!

Alex, there is heeeeaapps of room in the evo I reckon it's a good family car. Had my parents in the back and they had heaps more room!

You have to check it out! I seriously think this is the best cars I've owned and everyone around me is agreeing

Yeah they are pretty big inside, boot is huge too

But then it is a lancer :ninja:

yeah, they are surprisingly big,,,

trey on evolutionoz takes the 2 kids in booster seats and a pram around in his VII no worries

also remember... 4 doors for more whores

Aaron might need your guard help on Sunday coming up if end up getting scrubbing, wheels / tyres should be going on saturday

Should be free Sunday morning if you're into getting up early

i'm sure it has enough room in it for one of these babies (no pun intended)

8882e14971.jpg

i looked into those... but i ended up with this bad boy

3537-Diamond-AHR-Hazel_Forwar-Facing-no-mat-LR.jpg

has side impact cushions and even has speakers in the headrest so he can listen to biggie while we drive!

Biggie? Get the lil man onto reggae. Instead of an angry life he'll be jammin

one of my

best mate's boy is a massive fan of reggae. not two years old and he knows which button the station is preset to and how to turn it up.

Yeh but once u add baby seats prams and all the bullshit that goes with it most of the time can't even slide passenger seat back etc

I rkn if I ever have kids will be x5'in or similar for sure

pram goes in boot and i only have 1 kid (well i will in a few days) so he sits behind passenger seat and the mrs cant drive manual so no issues ;)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...