Jump to content
SAU Community

Recommended Posts

Hi,

I'm not sure if this should go here or in the General Maintenance Section but;

Today when I was driving to work, I started to drive up a hill and my Turbo's wouldn't engage. I looked out the rear mirror and the car wasn't blowing any smoke to indicate shagged Turbo's.

I thought it might have been the AFMs, but the last time I had an AFM die on me in the GTR the car would refuse to go above 4K rev's (Same thing with my old WRX) and a light would 'activate' on the dash on the right hand side (In the 4-cluster where the AWD light is) and it would just bog down when I tried to accelerate. This isn't happening this time.

However, as it is now, I can drive the car normally, it rev's out to 7K and feels like I'm driving an N/A car. The car just refuses to boost and on the standard 32 GTR 'boost' display it stops just before hitting 0. I can hear the Pod Filters sucking in a minute amount of air, but there's no blow-back when I take my foot off the accelerator.

Is there any way I can tell if this is an AFM, Turbo, ECU or Pod Filter without having to buy new parts? Obviously there's the standard "Take it to a Doctor" response, but if it's something simple that I could do myself, I'd rather do that, than take it to someone and have them waste their time on it being something simple.

Also, is there a possibility it could be the exhaust somehow? I noticed on the drive home that the exhaust sounded different to normal, can't really explain how it sounded different, I just know that it did.

Thanks in advance for any help provided :)

Link to comment
https://www.sau.com.au/forums/topic/380589-1991-r32-gtr-turbos-stopped-working/
Share on other sites

This happened to me.

My cat was totallllllllllllllllllllllly blocked (imploded after a run with an Evo..). Drop the exhaust before the cat and go for a quick drive - see if you get boost back :)

Edited by 10 4

The cat temp light will come on when the exhaust temp is too high and may damage your cat.

It doesnt know if your cat is stuffed.

Drop the exhaust and check the cat, and hope you don't find the turbine wheel in there too.

@Don: No, nothing out of the ordinary, one minute I had boost, next minute I didn't. And I'm running 5 pounds of boost (Which is the stock tuning I believe)

@Everyone else: Thanks for the help, I'll get it down to an exhaust place Thurs or Fri. It's probably time I thought about putting on a new exhaust anyway... Car is still stock standard ;)

Check that the wastegates haven't stuck open and are causing the turbos to not spool. As said above as well check that the cooler piping isn't split and that the cat isn't blocked.

The next step is to drop the exhaust off the back of the turbos and as said check that the exhaust wheels are still there.

Best of luck

I'm going to try and take it down to an exhaust place tomorrow and see if they can pull it off to have a look.

At least that way, I should be able to narrow down the problem.

I'd find it a little weird if it was the Turbo's themselves that had exploded/dropped parts, as there was literally no noise (Bangs, clunks, clangs, tingles, etc) when they stopped working. If they had dropped parts, I would probably have smoke out the exhaust as well, as it is... There's no smoke coming out at all.

I did manage to figure out how the exhaust sounded different though... It sounds strangled and muffled compared to normal... So that would say that there's some form of blockage. Fingers crossed this is an easy fix :)

And thanks to everyone for the help :)

Boost leak = black smoke

Broken turbo(s) = no boost at all, rough running when you try to put the motor into the conditions that would used to have made boost. No black smoke IIRC, and they can go with no/little noise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...