Jump to content
SAU Community

Recommended Posts

Hi,

I'm not sure if this should go here or in the General Maintenance Section but;

Today when I was driving to work, I started to drive up a hill and my Turbo's wouldn't engage. I looked out the rear mirror and the car wasn't blowing any smoke to indicate shagged Turbo's.

I thought it might have been the AFMs, but the last time I had an AFM die on me in the GTR the car would refuse to go above 4K rev's (Same thing with my old WRX) and a light would 'activate' on the dash on the right hand side (In the 4-cluster where the AWD light is) and it would just bog down when I tried to accelerate. This isn't happening this time.

However, as it is now, I can drive the car normally, it rev's out to 7K and feels like I'm driving an N/A car. The car just refuses to boost and on the standard 32 GTR 'boost' display it stops just before hitting 0. I can hear the Pod Filters sucking in a minute amount of air, but there's no blow-back when I take my foot off the accelerator.

Is there any way I can tell if this is an AFM, Turbo, ECU or Pod Filter without having to buy new parts? Obviously there's the standard "Take it to a Doctor" response, but if it's something simple that I could do myself, I'd rather do that, than take it to someone and have them waste their time on it being something simple.

Also, is there a possibility it could be the exhaust somehow? I noticed on the drive home that the exhaust sounded different to normal, can't really explain how it sounded different, I just know that it did.

Thanks in advance for any help provided :)

Link to comment
https://www.sau.com.au/forums/topic/380589-1991-r32-gtr-turbos-stopped-working/
Share on other sites

This happened to me.

My cat was totallllllllllllllllllllllly blocked (imploded after a run with an Evo..). Drop the exhaust before the cat and go for a quick drive - see if you get boost back :)

Edited by 10 4

The cat temp light will come on when the exhaust temp is too high and may damage your cat.

It doesnt know if your cat is stuffed.

Drop the exhaust and check the cat, and hope you don't find the turbine wheel in there too.

@Don: No, nothing out of the ordinary, one minute I had boost, next minute I didn't. And I'm running 5 pounds of boost (Which is the stock tuning I believe)

@Everyone else: Thanks for the help, I'll get it down to an exhaust place Thurs or Fri. It's probably time I thought about putting on a new exhaust anyway... Car is still stock standard ;)

Check that the wastegates haven't stuck open and are causing the turbos to not spool. As said above as well check that the cooler piping isn't split and that the cat isn't blocked.

The next step is to drop the exhaust off the back of the turbos and as said check that the exhaust wheels are still there.

Best of luck

I'm going to try and take it down to an exhaust place tomorrow and see if they can pull it off to have a look.

At least that way, I should be able to narrow down the problem.

I'd find it a little weird if it was the Turbo's themselves that had exploded/dropped parts, as there was literally no noise (Bangs, clunks, clangs, tingles, etc) when they stopped working. If they had dropped parts, I would probably have smoke out the exhaust as well, as it is... There's no smoke coming out at all.

I did manage to figure out how the exhaust sounded different though... It sounds strangled and muffled compared to normal... So that would say that there's some form of blockage. Fingers crossed this is an easy fix :)

And thanks to everyone for the help :)

Boost leak = black smoke

Broken turbo(s) = no boost at all, rough running when you try to put the motor into the conditions that would used to have made boost. No black smoke IIRC, and they can go with no/little noise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...