Jump to content
SAU Community

Recommended Posts

Hi guys, there’s one or two of these babies getting around Canberra and I think I should own one :)

if you know one of the owners or maybe know where one is, could you let them know im interested in making an offer for one.

this is what im looking for.

Nissan_R31_Skyline_Silhouette_GTS2.jpg

any help would be great, cheers

Link to comment
https://www.sau.com.au/forums/topic/381915-looking-for-a-car/
Share on other sites

I approached the faded GTS2 in Tuggeranong before. They weren't interested in selling. I think they're down lanyon way these days. I see it some times going past Calwell.

Pretty sure the second one was sold 4 years ago to a guy in Melbourne. I was a few hours off buying it myself.

Pffft Import a 4 door Passage

and get me one too!

Will keep an eye out though

passages are nice and i'd love one, but i much rather a GTS :P

Pick one :thumbsup:

(Skyline Nationals 2008)

hmmm.... the red one

I approached the faded GTS2 in Tuggeranong before. They weren't interested in selling. I think they're down lanyon way these days. I see it some times going past Calwell.

Pretty sure the second one was sold 4 years ago to a guy in Melbourne. I was a few hours off buying it myself.

yeah, seen him getting around down there. ive even taken too sitting on Tharwa Dr to see if i can find them. :ph34r:

  • 1 month later...
  • 1 year later...

I thought id post in here :)

I finally got the GTS i was after! Its seen better days, but its A1 mechanicly and i wanted it for a long term resto project anyway. all the good bits (bar two rims) are there including the origninal tape deck :geek:

P2110039_zps67e007af.jpg

I thought id post in here :)

I finally got the GTS i was after! Its seen better days, but its A1 mechanicly and i wanted it for a long term resto project anyway. all the good bits (bar two rims) are there including the origninal tape deck :geek:

P2110039_zps67e007af.jpg

Damn you, so jelly!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...