Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

i measured back pressure on a -10 equiped rb2630 we had at work that just would not makle power over 18psi.

on 14psi there was 25psi back pressure. on 18-20psi it had 35-40psi back pressure.... (30psi boost guage the needle wraped around to 0.. and our dyno can only read 30psi.

What power did that particular engine make on your dyno?

Just need someone with 2530/-5 to take the plunge and try a cropped GT30 exhaust wheel as above and use the HTA 68 front wheel and hope for the best! If its to laggie 3ltr it!!

you want me to try what? :D

i'm in Melb, dealt with Stao quite a bit before with my GT-T, nice little high-flow on that car, punchy little number.

So what are we trying to do with the 2530's? in laymans terms, i'm terrible when it comes to turbos, other than a 3071 is less laggy than a 3076, basic crap like that :D

are we trying to make them more responsive and powerful at the same time, or just more top-end out of them? I'm running 2530's in the R

Attempting to push 2530's harder! Whats the consensus of whether to open up the entry to the wastegate flap on hks 2530's? More area on the flap would apply more force to blow it open?

These could be my next upgrade (4th set) of actuators the dual ports look real nice!

http://www.full-race.com/store/turbos/borgwarner-efr/efr-dual-port-internal-wg-actuator.html

Now i wonder if running boost pressure to the bottom side of the gate will enable me to crack 30psi up top with the 19psi actuators or head straight to the 35psi units? Be interesting to see base pressure with the 35psi ones! :domokun:

The reliability of the stock extruded manifolds are great but at 460awkw i wonder if theres power there aswell?

Nice looking actuator!

Where did you get the manifolds extrude honed?

Berry's GTR used to be (still is?) on stock manifolds, surely they'd know if it's a restriction so maybe call CNJ Motors in Queensland and see what they have to say?

UAS organised the honing back in 2004 not sure if there still doing it..

Maybe hypergear could join the conversation with a few options on high flow bolt in low mount GTR turbo's that give 50-60AWKW extra than current offerings without masses of lag??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...