Jump to content
SAU Community

Recommended Posts

Twin scroll with be best.

I run a single scroll equal length love fab turbo header with a tial 60mm wg.

Spool test was at .7 bar no boost controller.

Results was:

5 psi at 3,200 rpm

10 psi at 4,300 rpm

Which was fool boost

We set our rev limit to 5,000 rpm

Which was hitting rev limit at 4,800rpm

You can check out Kelford camshafts

They use a lower lift but the same duration as my tomei.

Mine is 10.25 both camshafts

They do help spool

Why the super low boost level and rev limiter?? Are you running the engine in?

Twin scroll with be best.

I run a single scroll equal length love fab turbo header with a tial 60mm wg.

Spool test was at .7 bar no boost controller.

Results was:

5 psi at 3,200 rpm

10 psi at 4,300 rpm

Which was fool boost

We set our rev limit to 5,000 rpm

Which was hitting rev limit at 4,800rpm

You can check out Kelford camshafts

They use a lower lift but the same duration as my tomei.

Mine is 10.25 both camshafts

They do help spool

Kelfords camshaft listing for the rb25 is kinda unclear. It shows hydrilic lifters but says that its not suitable for the r33 an r34 with nvcs. So will these drop right into a series 1 rb25det with hydros...? No springs or solid lifters right....?

Why only 22psi? Just keep screwing more in until it stops making power or you run into detonation issues.

This is probably the smartest post of yours on SAU.

Why people stop at a certain number they get stuck in their heads is just STUPID

Lol

A high boost T78 will Demand tire changes like you wouldn't believe.

The demand wide rims to have atleast a 275 or a 300 wide tire to be able to find some grip.

This means rims less the 10j are useless unless you can afford good sticky dot tires with treadware 100 or less.

Plan ahead and get ready to spend some good cash on suspension and wheels/tires.

Learn how suspension works.

Become a expert in spring rates etc.

The more you know the less money you waste.

That's my 2cents

Why people stop at a certain number they get stuck in their heads is just STUPID

Ahh, whats stupid about it? A std engine with 9.0:1 compression on PULP98 is going to fall victim the laws of physics if you lean on it too hard.

A std 9.0:1 compression bottom end isnt going to like too many revs, too much boost or too much power in general. Mix all three together and you have to accept that the state you are running your engine in may result in a faiulure.

Keep revs to below 7,800rpm, boost under 20psi and I suspect the thing will be pretty reliable even if its making 360rwks. Run 24psi and the risk simply increases

Keep revs to below 7,800rpm, boost under 20psi and I suspect the thing will be pretty reliable even if its making 360rwks. Run 24psi and the risk simply increases

Why 20psi, why not keep it under 18psi?

You are guessing, really need to put it on the dyno and see how it behaves, if it doesn't detonate or get hot then what is the issue?

Edited by Rolls
  • 1 year later...

Update time.

Made 300kw on 16-17psi and e85.

I did end up with more but i was running out of fuel. I think it's time for a new fuel filter.

Will retune on 98 and e85 with more boost a bit down the track.

Out of interest what plugs should i be running?

What sort of timing no's should i expect up top? Currently it's around 17-18deg.

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...