Jump to content
SAU Community

Recommended Posts

yeah, its kind of like riding a rocket, you just know ist going to go hard but will also blow up eventually!!!

But for one lap it looks good.

well there were 3 458 GT3's in the top 10 at the end of the Sap 24hr this year, not bad for a car everyone seems to think won't last the 12 hours at bathurst

But what about the 4-5 DNFs~ :whistling:

I would still take a big lazy pushrod V8, flat 6 or V10/V12 over something that has to pull 9,000rpm for 24 hours. Still, was watching them at Spa a few weeks back. They are great looking things! Cant imagine the budget it would take to run one vs the Viper or Porsche

  • 3 months later...

back at it again this weekend, hours in before the ran the 458GT3 has set a new official lap record in the 12 hour a 2:06.3311 with another 4 cars under the V8 Lap record

http://www.natsoft.com.au/cgi-bin/results.cgi?26/02/2012.MOUN.R13

Edited by Whiplash

i doubt the v8's will break that record. this year is the last year they will have a chance, because under the COTF regs they will have less power, so will be lapping slower.

But they will have better suspension and handling. The GT cars peaked at around 260 - 270kph on conrod compared to the V8's knocking on 300kph. All the time is made up across the top of the mountain.

The GT cars have much better aero, but the driver reports on the COTF state that they handle a lot more like the Cup Cars

Don't forget COTF is considerably lighter than the current cars as well, and I would not be so certain about the loss of horsepower...

don't know if i'd call 100kg "considerably lighter". certainly lighter (enough to make a difference), but not massively lighter.

as for the power drop, it was mentioned in an article about the nissan v8 being used. power output is expected to be between 10 and 20% lower than it currently is, which is lower than what it was 5 or 10 years ago

You'd be mad to assume that COTF is to be slower than current cars.

Better suspension, transaxles, broader engines, specifically designed chassis instead of a monocoque.

It may take some time for engineers and drivers to grasp the chassis but they will be far from slower.

But what about the 4-5 DNFs~ :whistling:

I would still take a big lazy pushrod V8, flat 6 or V10/V12 over something that has to pull 9,000rpm for 24 hours. Still, was watching them at Spa a few weeks back. They are great looking things! Cant imagine the budget it would take to run one vs the Viper or Porsche

Because the commodores that were snapping timing chains do so much better in the Bathurst 12 hour...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...