Jump to content
SAU Community

Recommended Posts

yeah, its kind of like riding a rocket, you just know ist going to go hard but will also blow up eventually!!!

But for one lap it looks good.

well there were 3 458 GT3's in the top 10 at the end of the Sap 24hr this year, not bad for a car everyone seems to think won't last the 12 hours at bathurst

But what about the 4-5 DNFs~ :whistling:

I would still take a big lazy pushrod V8, flat 6 or V10/V12 over something that has to pull 9,000rpm for 24 hours. Still, was watching them at Spa a few weeks back. They are great looking things! Cant imagine the budget it would take to run one vs the Viper or Porsche

  • 3 months later...

back at it again this weekend, hours in before the ran the 458GT3 has set a new official lap record in the 12 hour a 2:06.3311 with another 4 cars under the V8 Lap record

http://www.natsoft.com.au/cgi-bin/results.cgi?26/02/2012.MOUN.R13

Edited by Whiplash

i doubt the v8's will break that record. this year is the last year they will have a chance, because under the COTF regs they will have less power, so will be lapping slower.

But they will have better suspension and handling. The GT cars peaked at around 260 - 270kph on conrod compared to the V8's knocking on 300kph. All the time is made up across the top of the mountain.

The GT cars have much better aero, but the driver reports on the COTF state that they handle a lot more like the Cup Cars

Don't forget COTF is considerably lighter than the current cars as well, and I would not be so certain about the loss of horsepower...

don't know if i'd call 100kg "considerably lighter". certainly lighter (enough to make a difference), but not massively lighter.

as for the power drop, it was mentioned in an article about the nissan v8 being used. power output is expected to be between 10 and 20% lower than it currently is, which is lower than what it was 5 or 10 years ago

You'd be mad to assume that COTF is to be slower than current cars.

Better suspension, transaxles, broader engines, specifically designed chassis instead of a monocoque.

It may take some time for engineers and drivers to grasp the chassis but they will be far from slower.

But what about the 4-5 DNFs~ :whistling:

I would still take a big lazy pushrod V8, flat 6 or V10/V12 over something that has to pull 9,000rpm for 24 hours. Still, was watching them at Spa a few weeks back. They are great looking things! Cant imagine the budget it would take to run one vs the Viper or Porsche

Because the commodores that were snapping timing chains do so much better in the Bathurst 12 hour...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...