Jump to content
SAU Community

Recommended Posts

hello everyone,

i recently got a 1990 gtr r32, and I'm having some problems with it.

1. extremly bad fuel consumption. my r32 can only do 3kms on 1 liter when I'm driving very gentle(shifting before 3k rpm). the car is slightly moded, according to the previous owner, the engine was rebuilt(with stock parts i think), kakimoto exhaust, custom turbo downpipes, apex intakes, boost restricter off, boost on 8psi, hks intercooler and stock turbos.

after i got the car, i put new ngk sparks in, and found the tip on those sparks i took out are really black(fuel), so i checked injector, but they are fine.

my question is will it be the o2 sensors, fuel pressure regulator, fuel pump or fuel filter?

and will a flashed ecu do this?(previous owner don't know if its flashed or not)

2. hicas. the hicas light on cluster comes on after a few km drives on highway, but goes away if i shut the car off and start again. if i jack the car up right after the light comes on, both rear wheels can be shacked right and left by hand, almost like the hicas is not doing anything, but if the light is off, wheels are perfectly good.

my question is whats wrong with my hicas?

i already ordered the hicas lock bar, I'm gonna install it either way, but when installing, is it better to take the whole hicas system off from the car or can i just loop the hydraulic line?

3. rear differential. my rear differential makes very big noise when wheels are turning and i happen to find a $300 used one for r32 from getjdmcars.com, its not here yet, but my question is, does the differential on r32s break ofter? should i upgrade it to a cusco 2way or 1.5 way one?

thats all questions i have now.

thanks for viewing and answering.

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/
Share on other sites

1. Will most probably be a dodgy o2 sensor not leaning fuel the way it should so just replace them first

2. Hicas system is over 20 years old and the hicas rack is probably just old and shit ! Just put a lock bar on it and don't worry bout hicas anymore ! I personally dont like it but each to there own

3. Is ur diff shimmed can u describe the noise ? Is it like it is lockin the wheels an chirping ? Or is it like its really sloppy lights up the inside wheel ?

never really herd or a gtr diff blowing just becoming sloppy and usually u would just shim it to tighten it ...

preety sure they are 1.5 way or something similar standard

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6121434
Share on other sites

1. Will most probably be a dodgy o2 sensor not leaning fuel the way it should so just replace them first

2. Hicas system is over 20 years old and the hicas rack is probably just old and shit ! Just put a lock bar on it and don't worry bout hicas anymore ! I personally dont like it but each to there own

3. Is ur diff shimmed can u describe the noise ? Is it like it is lockin the wheels an chirping ? Or is it like its really sloppy lights up the inside wheel ?

never really herd or a gtr diff blowing just becoming sloppy and usually u would just shim it to tighten it ...

preety sure they are 1.5 way or something similar standard

thanks for answering!

for o2 sensors, i see 2 around turbos and i know theres one more around catback, which one should i replace or should i replace all of them?

for hicas, i am installing the lock bar, but I'm not sure what should i do with those hydraulic lines, and can the whole system be removed completely?

for rear diff, I'm hearing "thump, thump, thump, thump" noise while driving around 10-30km/h, any speed after 40km/h it turns into a whining noise.

turning doesn't change the noise.

while turning rear wheels by hand, i can hear something like metal grinding noise.

a mechanic told me to shim it but i thought its not gonna last long so i ordered a used one.

the cusco 1.5way cost around 1.5k,, is it a good upgrade? or should i spend money on engine?

thanks a lot

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6121472
Share on other sites

1. How old is the battery?

If the battery is old, it will lose a lot of charge on startup. The alternator then starts pumping heaps of amps back to the battery to get it recharged. The ECU sees this amperage as some sort of error, and switches to a sort of limp mode that burns fuel like it was going out of fashion.

(the "O2 sensor" in the cat is the cat temperature sensor).

Have you had the injectors sonic cleaned?

Not "I ran injector cleaner", actually removed, cleaned and flowed in a sonic bath.

2. Try doing the HICAS diagnostic.

3. You have oil in the rear diff? Change the diff oil? (although it's probably shagged by now)

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6121535
Share on other sites

The clunking in the diff maybe caused by worn our shims not putting enough preload on the gears making them lose and and creating the clunking sound you describe which I think the most likely cause I would not by another one just pull it out and inspect and then get it shimmed shims from Nissan are only like 13 bucks if ur mechanically minded u could do it yourself ...

If not take it to a shop It should be around the 500 mark to get the work done I think whic is cheaper than a cusco as stated above factory gtr is a 1.5 way anyways ( I think )

As for sensors replace the 2 just after the turbos they are ute o2 sensors the one on the cat is actually a different sort of sensor it is connected to your light on your dash and will measure ur exaust gas temp it will tell ur ecu if it gets to hot meaning it's leaning out to much which indicates more servere problems which is a story for another day

With the hicas Just loop the lines so they run back to the pump ( bypass the hicas when u lock it ) if u buy a proper lock bar kit they should give you parts and info required for the job

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6121553
Share on other sites

1. How old is the battery?

If the battery is old, it will lose a lot of charge on startup. The alternator then starts pumping heaps of amps back to the battery to get it recharged. The ECU sees this amperage as some sort of error, and switches to a sort of limp mode that burns fuel like it was going out of fashion.

(the "O2 sensor" in the cat is the cat temperature sensor).

Have you had the injectors sonic cleaned?

Not "I ran injector cleaner", actually removed, cleaned and flowed in a sonic bath.

2. Try doing the HICAS diagnostic.

3. You have oil in the rear diff? Change the diff oil? (although it's probably shagged by now)

both battery and alternator is new,

the mechanic checked my car said injectors are fine so didn't sonic clean them

im installing the hicas lock bar either way, just want to know what do i do with the original plugs and hydraulic line.

the diff oil was changed recently and its still making noise

thanks

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6122255
Share on other sites

The clunking in the diff maybe caused by worn our shims not putting enough preload on the gears making them lose and and creating the clunking sound you describe which I think the most likely cause I would not by another one just pull it out and inspect and then get it shimmed shims from Nissan are only like 13 bucks if ur mechanically minded u could do it yourself ...

If not take it to a shop It should be around the 500 mark to get the work done I think whic is cheaper than a cusco as stated above factory gtr is a 1.5 way anyways ( I think )

As for sensors replace the 2 just after the turbos they are ute o2 sensors the one on the cat is actually a different sort of sensor it is connected to your light on your dash and will measure ur exaust gas temp it will tell ur ecu if it gets to hot meaning it's leaning out to much which indicates more servere problems which is a story for another day

With the hicas Just loop the lines so they run back to the pump ( bypass the hicas when u lock it ) if u buy a proper lock bar kit they should give you parts and info required for the job

i already ordered a $300 used rear diff for r32, so i guess this is cheaper.

i just want to know that incase the used one breaks too, should i upgrade it to a cusco 1.5way one? is it any good?

for o2 sensors, can i buy 2 widebands and put them in? can they connect to factory ecu or do i have to get a aem power fc or some sort?

thanks!

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6122256
Share on other sites

  • 3 weeks later...

Does the car have an aftermarket ecu or fuel pressure regulator?

Can u check ALL of the intercooler pipes and vacuum lines. If one or more is off the mapping will be out.

Check air flow meters

Set base ignition timing

Set TPS adjustment

Link to comment
https://www.sau.com.au/forums/topic/383709-r32-problems/#findComment-6151210
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah it is always worth testing and balancing actuators out of the box, just set the pressure regulator on a compressor very low (eg 5 psi) and increase it slowly to see when they both move.....unfortunately while you may be able to adjust the length of the actuator rod to minimise any difference, the actual pressure they move from is not adjustable so you need a well matched pair. And yes, the VCAM is probably contributing; the earlier in the rev range they come on boost and the slower the revs build (I think your demo was in 5th), the more you notice it.  Driving at WOT through 1st, 2nd, 3rd etc you will probably never hear it as any shuffling starts and is over super quickly
    • oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
×
×
  • Create New...