Jump to content
SAU Community

Recommended Posts

Hey Guys,

I pulled my front bar off yesterday to find that half my fins on my intercooler are bent over hard and this is most likely contributing or the source of my weird overheatign problems atm. So im going to get a new intercooler.

There are heaps of coolers for the 32/33 gtr but not many other than the 2k HKS kits for the 34.

Im looking at the cooling pro ones for the 32/33 GTR. I have HKS GTSS turbos so im not after massive power.

Question is: How hard is it to mount the sensor from the std 34 GTR cooler into those and is it even nessecary.

Next: Are there any physical differences in the mounting points etc etc.

Or if someone can suggest a replacement cooler for under 1k Im happy to listen

Link to comment
https://www.sau.com.au/forums/topic/384156-r34-gtr-intercooler-question/
Share on other sites

use a comb or a flat blade screw driver and straighten the fins, Just thinking of it there is a tool you can buy for it, I think most refrigerator repair shops sell them

annnndddd found one

http://www.awesome-gti.co.uk/product.php?xProd=36561

Are you talking about the intake temperature sensor?

If so, not necessary but it's not hard to do either. Just tap the holes for the screws or even get self tapping ones. Drill out the hole you need for the sensor and presto!

My sensor is hanging in the air at the moment as my cooler is not meant for the v-spec models. I'm waiting until I buy the hard piping kit then I will mount the sensor the same time the bar and cooler is off.

Greddy sell intercoolers with the sensor tappings in place as I had one on my old R33 GTR. I just had to use their blanking plate.

can you define the "weird overheating problems"

i would be totally gobsmacked if bent fins caused your weird overheating problems

ie; it doesnt make sense

bent fins could marginally affect inlet/outlet air temp but your wording sounds like water temp / radiator problems

are you mixing the two up?

Ok then.

I have a nismo radiator and thermostat.

The car used to run at 72-75.

It will now go to 75 then hop upto 77 then jump upto 85. If you stop it climbs up into the 90s. Once you start moving it gets back down to 80 then ever so slowly back to 75-77.

I have had it looked at by two workshops and everything seems fine to them. The cutch fan seems to throw a fair bit of air upwards but if you put your hand behind it, just doesnt feel as if its dragging much air through the radiator. Ine if the workshops put the dyno fan in front of the car and said it cooled back down then. So seems like an airflow problem. The car has been bled up a few times to elliminate air pockets, I have changed the coolant.

air lock in the coolant passages?

I too am with Paul now, if it is idling and getting hot than it isn't the intercooler, if you were cruising down the highway and it was doing it than yes, the cooler could be clocking air

Maybe the warmer weather has something to do with it? The fact that you are getting rising temps when sitting at lights is not an indication that the problem is the bent fins as no air will be passing through the radiator at that time. Your clutch fan is spinning and pushing air through the radiator(or sucking, I don't know) but the fact that you drive and it cools down to 75 is an indication that air is coming through. From 90c to 75c when you start moving.... its not luck, its functioning.

Edited by SargeRX8

Yeh im stuck on what to do. As I said the car has been bled a few times to get around an air lock.

I put my hand in near the front side of the radiator before and I could feel it sucking air through. I have had the car for about 6 months and I live in QLD so yes getting the hot weather, but still doesnt make sense for it to rise that much. Before the turbos went on it had no problem with the temps.

Oil temp is between 84-91 so that seems normal.

One of my turbo water pipes has a bit of a kink in it, but not enough to stop coolant flow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
    • So....knowing that I have a problem with power steering temps on track and another Wakefield day booked in next Friday, I've done the obvious thing They are very reasonably priced at $1650, considering they are a big monotube shock, double height adjustable (don't have to change pre-load to change ride height), one way adjustable damping and standard sized and customisable springs if you want something other than what comes with them. They come with 9kg/mm front and 4.5kg/mm front and I went with that as a starting point because I'll add adjustable sway bars too https://justjap.com/products/bc-racing-coilover-kit-ds-ds-infiniti-q50-v37-14-current#description Unfortunately they didn't come with rear strut tops so I've re-used the factory ones which was a bit of a pain. Also, the adjuster for the rear shock will be an absolute nightmare to get at, and while there are extensions in the kit I can't see any way you can actually attach or use them
    • I also had 2 bulbs blow at once, years ago in the stagea. made for a fun drive home. The issue was the voltage regulator had failed in the alternator and it was giving 15+ volts. Really, I was lucky all that was fried were the headlight bulbs. So, I'd suggest you check the voltage across your battery terminals with the car running and warmed up. Yes, you will need a multimeter to do so, sorry.
    • Good work to think to check that, and thanks for coming back to post up the outcome.
×
×
  • Create New...