Jump to content
SAU Community

Power Steering Problem Solving

Grungle

By Grungle,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Grungle Enthusiast

Grungle

Posted
Posted

After taking my car to a track day last week, the power steering hasn't been the same, so I'm looking for some problem solvers/diagnosis experts to think this through with...

I know the power steering overheated on the track. I let it cool down, then drove it home. No loss of fluid, but it was really heavy at very slow speeds. Fine at higher (+10km/h) speeds.

The next morning I sucked the fluid out of the reservoir (which looked clean, and didn't smell burnt), and refilled it. Started the car (cold) and turned the steering from lock to lock 5 times. No dramas - steering was light, no loud noises and the fluid level remained the same.

Took it for a drive, and after 10 minutes when the car was warm I pulled into a car park. The steering was HEAVY turning in. no assistance at all. I stopped, reversed (so revs went up) and had another go and the steering went light again. I then went forward, put it in neutral and with the engine now warm (idling at ~500rpm) the steering was really heavy when stationary.

I reversed out, took off up the road and went through some roundabouts - all good. Steering was light and felt like it always did.

Made it back home and once again, when the revs dropped to idle it lost the power assistance completely.

So I don't know much about power steering pumps...but this seems like a pump problem to me. I'm confused because is it's not completely stuffed - it works as long as the revs are over 1000rpm. Can a power steering pump "partially" fail? Is there anything else that could cause this issue? Leaking valves?

And finally, what's the best place to get a replacement pump? Has anyone got an old one sitting around? The missus will refuse to drive it soon...

Link to comment
https://www.sau.com.au/forums/topic/384489-power-steering-problem-solving/
Share on other sites
AAARGH 33 Community Regular

AAARGH 33

Posted
Posted

I had a similar problem but instead of the steering being heavy some of the time,mine was always heavy.

The fix was a genuine Nissan power steering pump overhaul/seal kit,I put in the new seals and she's all perfect.So maybe the seals are about to go in your pump,I'd go and by a pump seal kit if I were you.

bigkevracer Grand Master

bigkevracer

Posted
Posted

Ask Jetwreck. He cooked his power steering on the track, and warned me I'd need a cooler. He might be able to tell you what he did to fix it.

Seals might make sense though?

When I looked into the cooler, I found that everything else with a similar steering rack (350z, v35, pm35, etc) had a cooler, but we didn't.

Daleo Grand Master

Daleo

Posted
Posted

I have a small cooler to hook up to mine when I get a chance, any ideas which hose it needs to go into?

Hey Scotty,

It should go on the low pressure side of the system; so in the return line to the reservoir.thumbsup.gif

Grungle Enthusiast

Grungle

Posted
  • Author
Posted

I had a similar problem but instead of the steering being heavy some of the time,mine was always heavy.

The fix was a genuine Nissan power steering pump overhaul/seal kit,I put in the new seals and she's all perfect.So maybe the seals are about to go in your pump,I'd go and by a pump seal kit if I were you.

Yeah, that's what I don't get - if it was always heavy or leaking it would be easy. I guess early seal failure could show up like this.

i MAY have a 2nd hand pump in the garage from an M35

Can you PM me a price if you've got one? That sounds better than potentially waiting a couple of weeks for one from Japan. Nissan said they can probably get one, but they want the VIN before they order it.

funnily enough, after driving the car for just a short time you can feel the reservoir heat up quite quickly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • WMDC35
      R34 engine swap Rb25de neo to s1 Rb25det

      By WMDC35 · Posted

      If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • GTSBoy
      R34 engine swap Rb25de neo to s1 Rb25det

      By GTSBoy · Posted

      THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
    • GTSBoy
      Factory oil temp sensor in a RS4V without gauges?

      By GTSBoy · Posted

      Light should be a pressure switch, not a sensor.
    • Duncan
      Factory oil temp sensor in a RS4V without gauges?

      By Duncan · Posted

      The pressure light likely has a different sender to a pressure gauge, its been too long for me to remember for sure. Just have a look for another sender down near the oil filter. If you are confident in your rewired pressure sender reading correctly, you can be pretty sure it is just the dash light's sender failing, it is a pretty common thing.
    • Duncan
      C34 RSFour V Build in the US

      By Duncan · Posted

      It would be nice to see the result, but instagram is a click too far
×
×
  • Create New...