Jump to content
SAU Community

Recommended Posts

Hi, I have just installed the above boost controller.

It workes fine in 'OFF' mode (Standard boost) and i can get throught the whole rev range of the car but as soon as i choose a aftermarket setting and hit anything above atmospheric pressure, the car coughs, the hicas light flashes and it feels like it dies. Switch it back to 'OFF' and it boosts no problem.

The boost is set using a range of 0 - 100. when i set it to 0. I can boost with no problems (as 0 is standard) but once you go up a touch, like to say 5, it doesnt like it.

(For the pressure signal to the controller, I tapped into the line that goes from the fuel press reg to the manifold.)

Any suggestions?

Edited by GTSPWR
Link to comment
https://www.sau.com.au/forums/topic/385470-blitz-dual-sbc-spec-s-issues/
Share on other sites

My thoughts exactly. either wa iy i tried it 't'd where the standard gauge is connected to the manifold, and i get the same result. still dont understand why it wont boost past standard. additionally when i boost in off mode the standard gauge shows 6ish psi but the ebc shows .72 which would be closer to 10 psi???

where are you getting your power and earth from? I ask because hicas gives no shit about about a lot of things, boost pressure being one of them. However, if you're spliced into an earth trigger with a solenoid stuttering away giving an odd ball signal to the ecu......

Have you completely removed the factory boost control and blocked off any loose hoses?

The line between the FPR and the manifold is fine to use but the reason you DO NOT use it is because if that line pops off, or somehow you develop a leak to your boost sensor or something goes wrong with the boost sensor, you will loose pressure on your fuel rail and the engine will run lean and detonate.

There are many places. The best place is between the actuator and the hot pipe. From the manifold, you have the delay of pressure from the turbo to the throttle to the manifold. Between the actuator and the hotpipe is best because this is the pressure closest to the turbo so your boost controller can read the boost and control it as necessary. It might practically do jack shit but in my mind it feels like the closest point so to help prevent boost spike, get the source close and respond quick.

Spends alot of money on boost controller. Spend $0 on engine management. You may need to rethink priorities. Anything above 10psi the stock ECU will just go into R&R "Rich and Retard"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...