Jump to content
SAU Community

Recommended Posts

I have attached photo's of just a few of the parts I have available, please give me a call if you need any part of a R34 Im wrecking the entire car as it is a write off, my numbers 0400 508 382 call me anytime, if I don't answer leave a message, thanks.

post-89929-0-13094900-1325775311_thumb.jpg

post-89929-0-05887800-1325775338_thumb.jpg

post-89929-0-08009200-1325775345_thumb.jpg

post-89929-0-06846000-1325775352_thumb.jpg

post-89929-0-48695400-1325775361_thumb.jpg

post-89929-0-82866400-1325775368_thumb.jpg

post-89929-0-55448700-1325775377_thumb.jpg

post-89929-0-69886500-1325775384_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387344-r34-wrecking-have-heaps-of-parts/
Share on other sites

drivers side "a" pillar trim that goes over the door opening , black its in the 5th pic ( black one top left corner of the pic.) how much inc postage to nsw 2259

EJD001 I think it might cost about 10-20 bucks for postage? so give me $40 and ill ship it asap

chilzz - whats a SMIC? if its a computer part I have all the computers from the car.

and sorry troy no headlights.

oh righto, yeah I have the stock intercooler. Im not sure what there worth, so make an offer, and then unless you live near geelong, include postage, and ill ship it straight away.

no tail lights, they were smashed, but I have the sun visors, were you after both? can send both to brisy for $60 including postage, ill give you a pic on sunday? (theres nothing wrong with them)

no tail lights, they were smashed, but I have the sun visors, were you after both? can send both to brisy for $60 including postage, ill give you a pic on sunday? (theres nothing wrong with them)

Yes very keen for both does it come with clip as well??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...