Jump to content
SAU Community

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Yeah seems a bit of a problem with them.

To the guys that have had their M35 turbo blow, are the turbos dying due to bearing failure from oil supy issues or the ceramic turbine wheel coming apart then leading onto shaft/bearing failure?

Oil supply and poor servicing IMO. Coupled with the senario of it being a warranty item in Japan. Remember they run a lot more psi standard than the c34's. After they are rebuilt I haven't heard if any other turbo issues

Edited by Jetwreck

I don't think mine was either an oil supply nor servicing issue. My exhaust wheel just decided to part ways with the rest of the unit and was found in the cat, but yes it seems to be a recurring issue with M35's.

It's also a good excuse to start modifying (was the first mod on my old Stag lol). I'd be interested to see how long the stock turbo would last with an aftermarket dump and exhaust.

Exhaust restriction is one of the main culprits IMO

My thoughts are on the extra boost the M35 runs and shitty factory dump pipe causing excess heat and shaft speed on the turbine wheel.

I currently have an a/market dump and soon to add a front pipe with 200cpsi cat and keep the stock cat back, unless I come across a factory option Nismo system. Will be interesting how long my turbo will last. I oil change every 5000km and rarely give it any stick. Having said that, last week I relived my younger years by going up against a VE SS manual and VZ SS auto. Left the VZ a good 3 cars behind and the VE sat side by side. Boy did he look shocked ?. I didn't stall it up for either.

Edited by slippylotion

Yeah well not sure on the exact cause of why mine failed but the bearings were rooted and I think a bit of damage to the impeller.

So it's all getting replaced.

Anyway hopefully it will be back in car soon! What sort of a difference does the hiflow make? I've searched a bit for info but am yet to find much. Keeping in mind that everything else just about on the car is stock.

Will probably be looking at Jetwreck's banjo bolt mod when it's done to hopefully eliminate a but of potential for future issues.

Cheers

Nick

We have been over this before, if the oil supply stops, the rear bearing will fail fairly quickly. Definitely check the banjo if you hear the common jet turbine noise and get ready for a rebuild.

A highflow will do bugger all for the power output without tuning the ecu. All you will gain is lag unfortunately.

HKS make a filter- I have one in the kit that I did. Just goes in line with the braided lines. It is able to be taken apart and cleaned. The Japanese instructions that came with it said you clean every 5000kms. Don't know if worth it, but just putting it out there.

1_13_79.jpg

  • 3 weeks later...

I'm about ready for my car back... Going on a month at a mechanic recommended by my warranty provider. Getting part of costs covered.

I think the turbo was or is getting rebuilt by gcg.

Apparently there is only one mechanic at this workshop that knows how to put a turbo in and he's on holidays, only took him 8 hours because every bolt under there was stripped already... And quoted me on 8 hours getting it back in, yeah right.

Anyway this update should have come 3 weeks ago... But alas here it is, no need to say I'm a bit over it!

any reason for this comment? looking at getting an M35 through them...

Lets just say that some of their cars "coincidentally" have been known to have similar mileages; around the 50-65 000km area.:whistling:

That's not to say you won't get a good one; I bought mine from them and it had 39 000km (which I do believe to be fairly genuine). It's been basically perfect. :thumbsup:

Just make sure you see the original Japanese auction sheets PRIOR to laying any cash on the line. As with any sale, if it doesn't smell right; walk away.

Alex was great to deal with, but Dmitriy; not so much. Made a lot of promises, (all promises had been made via email) and then promptly forgot about them when it was time to deliver, Alex sorted most of it out.

I believe Dmitriy has since moved on, and is still on form...

All car yards will have bad stories; some due to genuine issues, some due to unrealistic expectations. There are a lot of good stories too, but people make the most noise when they feel they have been wronged.

Build a relationship with the dealer and I believe they will take care of you.

If you don't like the way you are treated in the beginning; I don't believe things will improve down the track, if you have an issue.

Edited by Daleo

yeah no worries, ive been speaking to a bloke named cody, really nice dude... just wanted to check in about that comment, this one has 43xxx on it, will ask to see the original JP auction paperwork.

Thanks for your help dale

Thread Jack.

Remember, cars can get a "hair cut" before they even make it to auction. So look for the tell tail signs of higher Kms- wear on gear sticks, steering wheels, carpets, rubber bushes under the car, and generally scruffier condition. Rust / corrosion (more than normal) on bolts and things under the car means a car thats come from a snow area with salted roads.

If in doubt, get an independent mechanical check over. thumbsup.gif

The Japanese de reg paper is what you want to see. That has the last 3 inspection dates and km recordings. Just make sure you see the original certificate and not a photo copy of the original.

Edited by slippylotion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...