Jump to content
SAU Community

Recommended Posts

There is a thing called:

Brake specific fuel consumption (BSFC)

It's a figure to describe how much fuel an engine needs to produce X amounts of power.

http://www.land-and-sea.com/dyno-tech-talk/using_bsfc.htm

There is a calculator on this page ->

http://www.rceng.com/technical.aspx

My (standard) injectors are now at 85% duty cycle, I am making about 330HP at the crank. (running at AFR of 11.7)

The mixture was starting to lean out already, so I have ordered new injectors.

Edited by Torques
  • 2 weeks later...

From my personal experience the standard injectors can hold more than most think. As my 33 gtst is making 393hp@wheels on standard injectors...

For the dyno figure doubters it does 119mph down quarter..

Edited by fragz013

My (standard) injectors are now at 85% duty cycle, I am making about 330HP at the crank. (running at AFR of 11.7) The mixture was starting to lean out already, so I have ordered new injectors.

Hmmm if you are finding that the fuel flow into the engine is levelling off at 85% IDC I'd consider looking at whats supplying fuel to the injectors more than the injectors themselves, personally - what pump is that with?

almost 300 rwkw? doubtful

119mph isn't a bad trap speed though, to be fair... though in saying that when you are limited by small injectors you can still make a car quite a bit faster than many would expect doing sneaky wee tricks. At lower rpm you have a longer pulse period, so you can actually move more fuel with an equivalent duty cycle.

As an example - I've tuned a Silvia running a G4 Link & boost control but still on stock injectors was quite held back, hitting 85% at 7000rpm at the boost level we were setting it up for. That boost level just wasn't going to do the setup justice, so I set up a "tapering" boost curve which resulted in a boost level some 6-7psi higher at 4500rpm than at redline and progessively dropping down... but injector duty cycles still never went over 85%. The resulting change in how the car performs is VERY substantial, torque wins races and hp sells cars?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...