Jump to content
SAU Community

Recommended Posts

Yer it does.. So does that mean I should or shouldn't get the dyno tune? Thanks

You need an aftermarket ECU to get a tune (unless you do a custom rom, but that sort of sucks). If you haven't changed anything on the car since the last tune was done, it might be a waste of time, however.

What ECU is it?

im not so sure about skylines, but with evos you can do a full tune with their factory ecu.

Theres always a good reason for a tune :) and generally theres always going to be some improvement made. how much improvement and what and the cost is what you need to weigh up.... Is it running quite bad? usually you can tell when its time for a tune.

Whats involved?? quite a lot of things actually but the basics are air fuel ratios, engine timing and boost. These things among others need to be set safe or be at safe levels or over time or a short time your engine will break or go boom. basically lol

The cost varies a bit depending on- Tuners pricing, Dyno time, alterations made during process and dyno type.

Ive done some research into getting a tune, as im also getting ready for a big day on the dyno, 2 days i think actually. The mechanic said it will be a day to alter the engine components like cams and fuel etc and full tune, then next day for cold start and road setup check. the price for the dyno tune alone is just under $1000 (not including installing cams and any mechanical work involved)

$900 to $1200 is a pretty fair range to expect for a tune.

One thing to note, a good tuner will only do very small alterations at the most. 9 times out of 10 they will save the setup, then wipe the whole ECU and start from scratch because they can never trust the current tune.

However you could also do a Dyno run or Power run.. (I just did one recently) it will give you power figures obviously, and will also give the tuner an indication on how your cars running and then he can tell you if he can make more power or if its running bad and needs re tuning etc etc.

only takes around 30 mins for a roller dyno and costs around the $100 - $150 mark

this is only based on my experiences over a few years in the scene.

im not so sure about skylines, but with evos you can do a full tune with their factory ecu.

Theres always a good reason for a tune :) and generally theres always going to be some improvement made. how much improvement and what and the cost is what you need to weigh up.... Is it running quite bad? usually you can tell when its time for a tune.

Whats involved?? quite a lot of things actually but the basics are air fuel ratios, engine timing and boost. These things among others need to be set safe or be at safe levels or over time or a short time your engine will break or go boom. basically lol

The cost varies a bit depending on- Tuners pricing, Dyno time, alterations made during process and dyno type.

Ive done some research into getting a tune, as im also getting ready for a big day on the dyno, 2 days i think actually. The mechanic said it will be a day to alter the engine components like cams and fuel etc and full tune, then next day for cold start and road setup check. the price for the dyno tune alone is just under $1000 (not including installing cams and any mechanical work involved)

$900 to $1200 is a pretty fair range to expect for a tune.

One thing to note, a good tuner will only do very small alterations at the most. 9 times out of 10 they will save the setup, then wipe the whole ECU and start from scratch because they can never trust the current tune.

However you could also do a Dyno run or Power run.. (I just did one recently) it will give you power figures obviously, and will also give the tuner an indication on how your cars running and then he can tell you if he can make more power or if its running bad and needs re tuning etc etc.

only takes around 30 mins for a roller dyno and costs around the $100 - $150 mark

this is only based on my experiences over a few years in the scene.

skyline ecu's can't be tuned that easily. r32 and some r34 ecus can have a daughter board installed which can be tuned. (r33's have to use a z32 ecu or a r32 ecu, but will lose the VCT with the r32 ecu).

as for always getting a gain from a tune, if he has an aftermarket ecu and the tune is decent then there won't really be any gains.

as for always getting a gain from a tune, if he has an aftermarket ecu and the tune is decent then there won't really be any gains.

+1. I wouldn't expect any gains.

However, for a new car it's not a bad idea to just do a power run to make sure whoever tuned it previously did a good job of it. Power runs are usually about $100.

Ok thanks for all the information about it and yer I'll just to a power run I think to see what he reckons I think it's going good but I just bought the car a week ago and just want to make sure it's all good.. So yer I'll get a power run and if it needs a full tune might do that but it's pretty pricy..

Thanks again

just ask around first, if hes a dodgy tuner he may say it needs one in order to get business ( i hope there arnt many around like that) also buy going to a top rated tuner that knows there stuff you know you are getting a reliable answer.

The dyno sheet can say its safe and all honkey dory but the tuner could also say it has more potential.

Like my one, its safe as houses, and has had a full tune a year or so ago by previous owner. But a new fuel pump its running a bit rich, and the tuner/s said it can and should be making a bit to a lot more from the power run.

As im new to Melbourne ive read a bit on the these forums and Ben at race pace is the man to see. thats where im going for my tune.

just ask around first, if hes a dodgy tuner he may say it needs one in order to get business ( i hope there arnt many around like that) also buy going to a top rated tuner that knows there stuff you know you are getting a reliable answer.

The dyno sheet can say its safe and all honkey dory but the tuner could also say it has more potential.

Like my one, its safe as houses, and has had a full tune a year or so ago by previous owner. But a new fuel pump its running a bit rich, and the tuner/s said it can and should be making a bit to a lot more from the power run.

As im new to Melbourne ive read a bit on the these forums and Ben at race pace is the man to see. thats where im going for my tune.

DVS JEZ has tuned plenty of Skylines with plenty of good results.

DVS JEZ has tuned plenty of Skylines with plenty of good results.

Helpful bloke too, has helped me out on a number of occasions and I'm not even in the same state as him. If I was in the same state, I know who would be tuning my car... thumbsup.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...