Jump to content
SAU Community

Recommended Posts

  • Replies 478
  • Created
  • Last Reply

Top Posters In This Topic

I'm definitely in, based on what else is needed to fit them... All listings state cars with factory HID's...However, most are removed for compliance.. If it's pretty straight forward to get these working... im in for a BLACK HOUSING set.. 2003 Coupe

^^^ incorrect. Despite the fact that Aus compliance states that ALL factory HIDs without self-levelling and self-washing facilities need to be removed to meet ADRs, when I was shoppping for a V35 I couldn't find one without HIDs! I think there are WAY more with HIDs than without.

But if you buy an aftermarket HID kit which are as cheap as $200 now you could fit them into these new lights with basic meachnical/auto electrical skills. You only need to modify a couple of wires, and install a power wire to the battery on a relay. I did it on my S15 and R34 - pretty easy job!

the seller said Zenki (early) and Kouki (late) models are both ok.

Confirmed List:

Chrome housing:

1. 4evershiva

2. 81gSKy y

3.Nightcrawler

4. Thinktea

Black housing:

1.Dreadnought

2.Megahowler

3.Runner4life

Edited by shiva

the seller said Zenki (early) and Kouki (late) models are both ok.

Confirmed List:

Chrome housing:

1. 4evershiva

2. 81gSKy y

3.Nightcrawler

4. Thinktea

Black housing:

1.Dreadnought

2.Megahowler

3.Runner4life

DO you have a pic of the back of these lights? im curious if the have the factor HID hole that fits the ballast and then you run the wires through the headlights and then use the HID bulb??

See the below pic, look at the area above the white box, thats where the factory HID ballast goes..

http://www.sabersport.com/Merchant2/images/headlight/02-AZ-IG03-PCC-HID-RF-2D-02.jpg

my car has hid lights, couldnt tell you if they are factory. they where there when i bought it. im not the first owner in aust. but if they will work with any hid's ill def be in for a chrome set. thanks

hey Sheldon, can you give a plain and simple answer so everyone's question can be answered.......i know you had some trouble to get the LHD to RHD in your lights but apart from that is it a big deal to get the lights fixed into the car with RHD specifications and is it legal?

Jesse's Payment options:Direct your enquiries to [email protected]

for a larger order like this an international transfer will work out a

little cheaper.

bank charges and options are as follows.

Paypal <- will be instant and you have buyer protection, Im also

protected from exchange rate changes as I can send you the bill in

JPY. Has a 4% fee and they dont give the advertised exchange rate ,

works out the most expensive way to transfer money.

Local transfer in AUD to my NAB account <-this has no buyer

protection, Im open to exchange rate changes so can be burnt if the

AUD takes a quick dive. no straight fees but the rate they give is

~3.3yen down on the advertised exchange rate. This is how I do most

of my transfers from Aus due to ease of transfer for the customer and

cheaper rates than Paypal.

International Transfer <- slow, a little complicated for you to send

money, takes a week for the money to clear into my Japanese account.

No buyer protection. They will give the advertised exchange rate and

as the money can be sent in JPY Im safe from exchange rate changes.

They do have large flat fees though, depending on the bank you use

on your side fees range from $0 to $25 and then there is an additional

4000yen receiving fee on my side. This kind of transfer only works

well with transfers over ~$1500 worth (this is how most car exporters

move money around)

Im ok with any of those ways so which ever suits you is ok.

*Ill only need the purchase cost of the tail lights up front and will

charge my commission and shipping costs after they have reached me and

have been weighed up.

Jayce - I Have aftermarket headlights from U.S

I have attached the link below.

Took me and A mate about 5 hours - hard bit is getting front bumper off. But second time its simple with practice. Sock might be easier - have the nismo one.

Post me with any questions mate.

3470-projector-headlights.asp&docid=vCQhRAQNqisyRM&imgurl=http://www.slickcar.com/products/LHP-G35032JM-TM9241885E-02.jpg&w=750&h=750&ei=-PVXT8b3OuyhmQW4m-DADw&zoom=1&iact=hc&vpx=610&vpy=193&dur=234&hovh=225&hovw=225&tx=95&ty=153&sig=110179230568841931979&page=1&tbnh=142&tbnw=142&start=0&ndsp=22&ved=1t:429,r:13,s:0&biw=1151&bih=786

Jesse's Payment options:Direct your enquiries to [email protected]

for a larger order like this an international transfer will work out a

little cheaper.

bank charges and options are as follows.

Paypal <- will be instant and you have buyer protection, Im also

protected from exchange rate changes as I can send you the bill in

JPY. Has a 4% fee and they dont give the advertised exchange rate ,

works out the most expensive way to transfer money.

Local transfer in AUD to my NAB account <-this has no buyer

protection, Im open to exchange rate changes so can be burnt if the

AUD takes a quick dive. no straight fees but the rate they give is

~3.3yen down on the advertised exchange rate. This is how I do most

of my transfers from Aus due to ease of transfer for the customer and

cheaper rates than Paypal.

International Transfer <- slow, a little complicated for you to send

money, takes a week for the money to clear into my Japanese account.

No buyer protection. They will give the advertised exchange rate and

as the money can be sent in JPY Im safe from exchange rate changes.

They do have large flat fees though, depending on the bank you use

on your side fees range from $0 to $25 and then there is an additional

4000yen receiving fee on my side. This kind of transfer only works

well with transfers over ~$1500 worth (this is how most car exporters

move money around)

Im ok with any of those ways so which ever suits you is ok.

*Ill only need the purchase cost of the tail lights up front and will

charge my commission and shipping costs after they have reached me and

have been weighed up.

I should allaborate a bit on my previous post - for everyones benefit.

Long story short;

- Factory HID's - Fitted straight into my Headlights from the U.S. They sit perfectly in the aftermarket metal clip and the ballast screws to the bottom - per stock set up.

- Yes - you can do it yourself - there is no wiring required - unless you want to light up the Halo's (I only have the LED sttip). In which case - Cut wire and solder it in. The front bumper needs to be removed. give yourself 5 hours or so if you havent dont this before from start to finish.

- NO they will not be legal. However - most workshops will give you a roadworthy but just notify you that if you're asked to take them out due to defect - do it.

- The lights will not point correctly immediateley after install.... you will need to spend time toggling the left and right / up and down screws in the back of the lights. You need to understand where the stock set up points - so you can adjust accordingly. Test this about 15M from a wall and If possible mark on the wall where the stock set up sits. On the V series you will notice the left light points slightly higher and to the side of the road. The right hand light (the one that will shine in traffic's eyes) needs to be put as low and straight as practically possible. This can alleviate some of the problems with no self leveling.

If anyone needs tips, Im happy to help out. Done the job on two cars now....and I work in Bank - so any one can do it!

Cheers

Thanks for the info dude but we are planning on getting these from japan, which should be RHD compliant, so we dont have to fiddle with the light settings.......

I should allaborate a bit on my previous post - for everyones benefit.

Long story short;

- Factory HID's - Fitted straight into my Headlights from the U.S. They sit perfectly in the aftermarket metal clip and the ballast screws to the bottom - per stock set up.

- Yes - you can do it yourself - there is no wiring required - unless you want to light up the Halo's (I only have the LED sttip). In which case - Cut wire and solder it in. The front bumper needs to be removed. give yourself 5 hours or so if you havent dont this before from start to finish.

- NO they will not be legal. However - most workshops will give you a roadworthy but just notify you that if you're asked to take them out due to defect - do it.

- The lights will not point correctly immediateley after install.... you will need to spend time toggling the left and right / up and down screws in the back of the lights. You need to understand where the stock set up points - so you can adjust accordingly. Test this about 15M from a wall and If possible mark on the wall where the stock set up sits. On the V series you will notice the left light points slightly higher and to the side of the road. The right hand light (the one that will shine in traffic's eyes) needs to be put as low and straight as practically possible. This can alleviate some of the problems with no self leveling.

If anyone needs tips, Im happy to help out. Done the job on two cars now....and I work in Bank - so any one can do it!

Cheers

*** Light comes on in Brain***

My bad - yes i see that now! Best of luck with it.

I can recommend importmonster.com.au in that case. Lots of OEM bits.

Cheers

Thanks for the info dude but we are planning on getting these from japan, which should be RHD compliant, so we dont have to fiddle with the light settings.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...