Jump to content
SAU Community

Recommended Posts

Yehh, results would be excellent :glare:

Haha would use E85 if it was an option here, but I'm not paying $3 a litre. Until it becomes more available, I'll be on PULP.

It'll happen man!! No rush ;)

Hope you get the E85 over there one day soon!

Haha yeh, would be good. At the moment I'm more likely to go WMI, it's just way easier. To be honest though, I think any more engine mods are on hold for awhile. Whatever power it makes with this tune is where it will stay for now. I just want to drive the damn thing again. The original plan was to have it ready for the reopening of Barbegallo, but I've overshot that by about 2 months now :( Dying to hit the track again.

Actually next money might be on a lap-timer, I still don't know what I'm getting around Barbs :unsure:

So the saga continues... Engine failed on the dyno today. Valves are sticking open. Don't even know where to start, but tomorrow I have to pick the car up and get it home. No idea where it goes from here.

So the saga continues... Engine failed on the dyno today. Valves are sticking open. Don't even know where to start, but tomorrow I have to pick the car up and get it home. No idea where it goes from here.

Boo

Timing belt?

Unfortunately RBs are interference motors :(

So sad to hear this man!

Nothing so obvious. If it had been a complete engine failure then I could just buy a new motor. But according to Sean, mine is still drive able. It's only when he tried to do a full load power run that the engine loses compression and he has to abort.

Nothing so obvious. If it had been a complete engine failure then I could just buy a new motor. But according to Sean, mine is still drive able. It's only when he tried to do a full load power run that the engine loses compression and he has to abort.

This has been burning my brain man! It doesnt add up....

  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...