Jump to content
SAU Community

C34 Stagea Reliability

GRK35L

By GRK35L,
in Four Door Family & Wagoneers

 Share

Recommended Posts

GRK35L Rising Star

GRK35L

Posted
Posted

Hi all,

I have recently sold my V35 and am looking to move into a C34 nissan stagea as a daily. I am looking at a series 2 model and was wondering how the car is in terms of reliability? I will be using the car as a daily so it is important to know that the thing will be reliable and be hassle free. The particular example I am going to look at is completely stock standard and I plan to leave it that way (lets see how long that lasts) to keep it reliable as a daily (I am going to purchase a weekender as a toy shortly). The only mod I may complete is a Stereo upgrade but that is it.

As said before the example I am looking at is bone stock with 84 200km on the dash. The owner is doing the whole moving over seas thing and I will be getting the car inspected before purchase.

Now I have looked at the C34 buyers guide before but I just would like owners to comment on reliability and common problems that occur on the stagea.

I appreciate any feedback given.

I am going to look at the car this weekend.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/395642-c34-stagea-reliability/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

I am on my 3rd C34 (Sold the first one because it wasn't a turbo, wrote off the second one) and I would say they are very reliable. the only problems I have observed with others are fuel pump failures and starter motor failure. Starter motors and alternators are often replaced in all types of vehicles after a high mileage and the same could be said of electric fuel pumps. At 84,000 if genuine you shouldn't have any problems.

With very high mileage examples you will of course need plugs and possibly coils but neither of these will leave you stuck at the side of the road - you will notice if they start breaking down.

Cowboy1600 Grand Master

Cowboy1600

Posted
Posted

Coil packs, rear left wheel bearing and rust under mirrors are about the only issues to expect.

Other than that, they are a mix of essentially an R33 GTR (drivetrain [note ESSENTIALLY]) and R34 GTT (engine). The rest is typical Nissan.

I've got two sunroofs, neither leak. Everything else is tight, box doesn't crunch, all the various handles and buttons still work etc etc (on car with 125,000ks).

I'd replace the o2 sensor the moment you get it home and give it an oil change with filter. Get box and diff fluids changed as well, just so you know precisely when it was all done last.

Other than that you should get years of happy motoring. Just be aware that they are heavier than a Skyline so do use a bit more fuel. I get about 14L/100ks with generally spirited driving (12psi) and pretty much no long trips (it's all either a blast across from Hurstbridge to Laurimar or a slow shuffle around Hurstbridge, Eltham, Diamond Creek and G'boro).

I'm really beginning to gel with my Stag and love it nearly as much as I did my 33. The practicality of a station wagon really is shit hot. My first car was a shaggonwagon and I fecking loved the room. Now I've got the room with comfort and performance! Winning!

GRK35L Rising Star

GRK35L

Posted
  • Author
Posted

The practicality is the whole reason I want one. as for fuel consumption that is a little less than the V35 so that is fine with me. If I get this one for the right price it will leave me enough $ to do all the fluid changes and such.

Coil packs, rear left wheel bearing and rust under mirrors are about the only issues to expect.

Other than that, they are a mix of essentially an R33 GTR (drivetrain [note ESSENTIALLY]) and R34 GTT (engine). The rest is typical Nissan.

I've got two sunroofs, neither leak. Everything else is tight, box doesn't crunch, all the various handles and buttons still work etc etc (on car with 125,000ks).

I'd replace the o2 sensor the moment you get it home and give it an oil change with filter. Get box and diff fluids changed as well, just so you know precisely when it was all done last.

Other than that you should get years of happy motoring. Just be aware that they are heavier than a Skyline so do use a bit more fuel. I get about 14L/100ks with generally spirited driving (12psi) and pretty much no long trips (it's all either a blast across from Hurstbridge to Laurimar or a slow shuffle around Hurstbridge, Eltham, Diamond Creek and G'boro).

I'm really beginning to gel with my Stag and love it nearly as much as I did my 33. The practicality of a station wagon really is shit hot. My first car was a shaggonwagon and I fecking loved the room. Now I've got the room with comfort and performance! Winning!

wolverine Grand Master

wolverine

Posted
Posted

I am on my 3rd C34 (Sold the first one because it wasn't a turbo, wrote off the second one) and I would say they are very reliable. the only problems I have observed with others are fuel pump failures and starter motor failure. Starter motors and alternators are often replaced in all types of vehicles after a high mileage and the same could be said of electric fuel pumps. At 84,000 if genuine you shouldn't have any problems.

With very high mileage examples you will of course need plugs and possibly coils but neither of these will leave you stuck at the side of the road - you will notice if they start breaking down.

Geez, Bob you have been unlucky with starters and alternators.

66yostagea Grand Master

66yostagea

Posted
Posted

Have had an S1 for 6 years. Only problem, not caused by me, the AF meter konked. Got 166k on it. Have another that has done same ks and the starter motor is on the way out.

StageaMang Apprentice

StageaMang

Posted
Posted

i bought a 1999 S2, RS4-S 5 speed with 64,000 on the clock for $15,000 3 years ago. so its a R34 engine with the R33 GTR running gear.

Best car i have ever had, its a wagon but drives and sticks to the road like a sedan. The response through the steering wheel is like driving a go-cart so fast and nimble.

Im a hills driver and its unreal what you can get away with man. (i used to have a RX7 half the weight and i can go harder in this thing that that.)

The turbo's are puss though, they are made from plastic well nylon bearings anyway so if you want to do hard hills driving (on off boost heaps) you will melt and warp the internals of the turbo eventually.

I got to 80,000 in mine and the turbo was literally melted.

Decided to go for a rebuild/ high flow on the turbo insted of bolting some massive lagy snail on it. The rebuild was 2000 buks and the thing is indestructible now. it can take over 20psi boost

Did an exhaust, air pod, mid sized inter-cooler (i recon big inter-coolers promote lag), new shockers and clutch just recently and the thing is a dream to drive and it blows off new Holden's and Fords with out an issue.

I can put our new born in it and drive normally/ sensible and when he and the misses are out, i can Cain the crap out of it and not have to worry.

If you drive these cars like a nanna then you never have an issue.

If you like to give it some stick then u will go through the normal clutches frequent oil and filter changes, tyres etc alot more. but thats with any car, the difference whit these things u feel safe and in control doing it.

I really feel like i ranted on a bit dude but i love these things and you need to get one :)

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

i bought a 1999 S2, RS4-S 5 speed with 64,000 on the clock for $15,000 3 years ago. so its a R34 engine with the R33 GTR running gear.

Best car i have ever had, its a wagon but drives and sticks to the road like a sedan. The response through the steering wheel is like driving a go-cart so fast and nimble.

Im a hills driver and its unreal what you can get away with man. (i used to have a RX7 half the weight and i can go harder in this thing that that.)

The turbo's are puss though, they are made from plastic well nylon bearings anyway so if you want to do hard hills driving (on off boost heaps) you will melt and warp the internals of the turbo eventually.

I got to 80,000 in mine and the turbo was literally melted.

Decided to go for a rebuild/ high flow on the turbo insted of bolting some massive lagy snail on it. The rebuild was 2000 buks and the thing is indestructible now. it can take over 20psi boost

Did an exhaust, air pod, mid sized inter-cooler (i recon big inter-coolers promote lag), new shockers and clutch just recently and the thing is a dream to drive and it blows off new Holden's and Fords with out an issue.

I can put our new born in it and drive normally/ sensible and when he and the misses are out, i can Cain the crap out of it and not have to worry.

If you drive these cars like a nanna then you never have an issue.

If you like to give it some stick then u will go through the normal clutches frequent oil and filter changes, tyres etc alot more. but thats with any car, the difference whit these things u feel safe and in control doing it.

I really feel like i ranted on a bit dude but i love these things and you need to get one :)

Wow! If I didn't have one already I'd rush out and buy one!:cheers:

pipster11 Grand Master

pipster11

Posted
Posted

just to clear up the misinformation from StageaMang

The impeller is made from nylon, the rear from ceramic, you won't "melt" the nylon because its on the intake side of the turbo

if you get enough heat into the turbo tho, you will melt the glue that holds the wheels onto the shaft

a hypergear highflow is about $800, nistune + tune is around $1000, add a new fuel pump for safety for $200 and you can have around 200awkw for a decent price (assuming you have an aftermarket exhaust already)

i've put around 40,000kms on mine, driven from the gold coast to tassie and back twice, used it as my daily to get to uni and deliver pizzas and its been great

only things i've had to change are:

timing belt (100,000kms service, got a free waterpump with it so changed that too, whole kit was $260 out of the US! INCLUDING A GENUINE WATERPUMP!!!)

new radiator (top tank cracked, $220 for a kotorad radiator off ebay)

lots of oil changes (i change at 5000 kms because i use a semi-syn, but its overkill really)

new o2 sensor (only about $70 and most of them need doing anyway)

because of the parts interchangeability you can upgrade things really easily, and quite cheaply too

so maybe look out for one with a few things done to it already and same some $$$

XRATED Veteran

XRATED

Posted
Posted

If nothing else, get a nistune type 4 board. There is ALOT of fuel to save and alot of midrange power and torque to be had with a simple tune. I have very basic mods and we picked alot of torque before 4500rpm.

J.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...