Jump to content
SAU Community

Recommended Posts

Yeah as above, make sure its on the return line. Shouldnt have any issues with flow really, there shouldnt be much pressure drop through the cooler and the pump should be able to push the oil through a cooler. Remember it does push the oil back uphill when it returns to the reservoir anyway

Random plug is the power steering pressure switch. Basically tells your ECU that the power steering is active and the ECU compensates to keep the revs steady

I don't really see that being a problem (besides maybe the cooler not being in the 'coolest' place), you shouldnt have any issues with feeding oil back. The cooler (once full) is not alot different to it just being a hose. There is probably a slight amount more restriction, but seems weird that you are having issues with this setup

Weird eh? Mine runs exactly the same and it runs perfectly.

I didn't even bleed it, just started the car and turned the wheel back and forth at the same time topping up thr reservoir. Happy days, perhaps see if there's a blockage somewhere.

I've done the same setup on another car years ago, no dramas there too (although was a poster street car that never saw the track).

  • 1 month later...

Matthew, I got quoted around $100 for the single power steering pipe, however I wasn't sure that was the only thing leaking.

I ended getting the entire power steering piping swapped from another R34, cost about $400 with labour.

No more leaks.

  • 10 years later...
10 minutes ago, GTSBoy said:

Ever seen a sock on a PS reservoir in a Jap video and wondered why?

Not until I googled it, now I remember lol. Seems like it's just to clean it up. But it doesn't stop the leak, I have a leak issue though? Thinking whether I need a new bottle, surely not lol.

Fluid gets hot, expands, comes out the cap. The seal might be old, dry and cracked....but realistically, this is something that has been happening since long before the seals should be able to be considered to be old and dry and cracked.

A better PS fluid cooler is a helpful thing. I plumbed the trans cooler from an R34 into mine. Deleted the near useless loop of hardline in front of the radiator that Nissan thought would do the job.

23 hours ago, silviaz said:

Not until I googled it, now I remember lol. Seems like it's just to clean it up. But it doesn't stop the leak, I have a leak issue though? Thinking whether I need a new bottle, surely not lol.

If there's no rubber gasket you need a new cap. There should be a rubber gasket, depending on the car. If you are driving the car hard and the power steering is getting hot it will spit out of the reservoir. I have seen people tap the cap for a hose + overflow catch bottle placed somewhere that it will fit. 

9 hours ago, GTSBoy said:

Fluid gets hot, expands, comes out the cap. The seal might be old, dry and cracked....but realistically, this is something that has been happening since long before the seals should be able to be considered to be old and dry and cracked.

A better PS fluid cooler is a helpful thing. I plumbed the trans cooler from an R34 into mine. Deleted the near useless loop of hardline in front of the radiator that Nissan thought would do the job.

There is no seal, that's the thing.

3 hours ago, joshuaho96 said:

If there's no rubber gasket you need a new cap. There should be a rubber gasket, depending on the car. If you are driving the car hard and the power steering is getting hot it will spit out of the reservoir. I have seen people tap the cap for a hose + overflow catch bottle placed somewhere that it will fit. 

I'm not sure if skyline's have it, I haven't been able to find info on it.

3 minutes ago, GTSBoy said:

Hence why I didn't dwell on the seal aspect of the discussion and talked about why it overflows and what can be done to help.

Ah right, I wasn't going to mess around and install extra crap. Surely it should work right out of the factory lol

Edited by silviaz
On 7/28/2024 at 4:02 AM, silviaz said:

Ah right, I wasn't going to mess around and install extra crap. Surely it should work right out of the factory lol

What specific car is this? I know for sure my R33 has a rubber sealing gasket on the cap. Not unusual to get a bit of seepage from it either.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...