Jump to content
SAU Community

Recommended Posts

Not sure about the crank but I would assume they are. The block may be different depending if it is a series 2 or 1 r33 block since the 33 S1 didn't have vct the oil galley will be different to the 34 head

Not sure about the crank but I would assume they are. The block may be different depending if it is a series 2 or 1 r33 block since the 33 S1 didn't have vct the oil galley will be different to the 34 head

All Rb25's have vct

The way to find out would be to compare a standard piston with your CP ones . I think the chamber sizes are different R33 R34 DET heads so you would need to buy R34GTt specific pistons to get the static CR right .

Should always measure anyway , cheers A .

all parts are for r33det, only the block and crankshaft is from r34. The CP piston used is SC7305 (which has 9:1CR 86.5mm). The compression height for for the 9:1CR and 8.5:1CR is the same.

"CP Pistons said that the valve reliefs are the same for both the 8.5 and 9.0 pistons. They say they design the pistons to accept high lift and +1.0mm oversized valves."

If the above is true, than r34 block or crankshaft is different to r33. Has anyone done this before (ie using r34 block/crankshaft and everything else are to suit r33)?

Will measure the stock piston.

I know for sure that r34 and r33 pistons are different (different in compression height.

Can you take a picture of how far it protrudes above the deck and post it on here?

all parts are for r33det, only the block and crankshaft is from r34. The CP piston used is SC7305 (which has 9:1CR 86.5mm). The compression height for for the 9:1CR and 8.5:1CR is the same.

"CP Pistons said that the valve reliefs are the same for both the 8.5 and 9.0 pistons. They say they design the pistons to accept high lift and +1.0mm oversized valves."

If the above is true, than r34 block or crankshaft is different to r33. Has anyone done this before (ie using r34 block/crankshaft and everything else are to suit r33)?

Will measure the stock piston.

I know for sure that r34 and r33 pistons are different (different in compression height.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...