Jump to content
SAU Community

Hard To Idle After Turbo Install

FordyR31

By FordyR31,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

AngryRB Grand Master

AngryRB

Posted
Posted

Avoid driving it dude, because lean afrs on cruise can and will burn your exhaust valves.

why would it be lean on cruise? i think your right with any boost it is leaning out, that must be why the light started flashing on mine, or maybe the tune.:whistling:

FordyR31 Mentor

FordyR31

Posted
  • Author
Posted

Here is how the intake was setup when it was stalling.

IMG_3970.jpg

This is how I had it afterwards to fix the stalling. I'm more convinced it was the ripples in the flex pipe than the extra length and bend, obviously had the air filter on for the test, this was taken before I put it on for the sake of the pic :).

IMG_3972.jpg

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

Its the angle the BOV enters, not the bend that causes the stalling imo. It looked like a nice intake until you ditched the airbox. :thumbsup:

I have to agree with scotty here

You can imagine the BOV just venting and bouncing around in all directions disrupting the flow.

When Scotty designed mine it dumps into the intake on an angle towards the turbo

The Mafia Grand Master

The Mafia

Posted
Posted

Yet another thread full of mafia's condescending crap, i hope it makes you feel tough :thumbsup:.

Not really hey, I've seen the AFRs after many of these upgrades and I know for a fact that they run lean and its not advisable to drive them far or at all.

So, dribble your shit elsewhere.

why would it be lean on cruise? i think your right with any boost it is leaning out, that must be why the light started flashing on mine, or maybe the tune.:whistling:

I wondered the same thing, but I've seen it on a few cars.

I'm thinking that at 2,500rpm and above the turbo is spooling a tiny bit, making the air path easier into the motor. Being a bigger turbo, its able to help more air into the engine. Think about it, at those revs, the turbine is spinning at a notable speed. The compressor would be "helping" the air get into the engine easier on vacuum, allowing it to breathe easier.

What had been tuned to 14.5 - 14.7 afrs on cruise, I'd seen go above 15. Also caused the engine to run a little hotter at cruise due to being a little leaner.

Not all but a number of cars.

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

Oh no not a 5% rise in AFR's, how on earth are the exhaust valves going to survive that. Load is determined by the AFM, unless theres a leak or something else isnt working as it should then its fine to drive normally. Sure the AFR's arent always going to be EXACTLY the same as they were before but your not going to kill your motor by driving it around under light load. It takes AFR's upwards of 17-18:1 to do any damage to valves and pistons under light-medium load and you'd know all about it if it was that lean.

AngryRB Grand Master

AngryRB

Posted
Posted (edited)

Not really hey, I've seen the AFRs after many of these upgrades and I know for a fact that they run lean and its not advisable to drive them far or at all.

So, dribble your shit elsewhere.

I wondered the same thing, but I've seen it on a few cars.

I'm thinking that at 2,500rpm and above the turbo is spooling a tiny bit, making the air path easier into the motor. Being a bigger turbo, its able to help more air into the engine. Think about it, at those revs, the turbine is spinning at a notable speed. The compressor would be "helping" the air get into the engine easier on vacuum, allowing it to breathe easier.

What had been tuned to 14.5 - 14.7 afrs on cruise, I'd seen go above 15. Also caused the engine to run a little hotter at cruise due to being a little leaner.

Not all but a number of cars.

i agree to this , the engine seems more powerful even without boosting compared to my old highflow i had, and that is significant , and its odd but i think true... and with cams i find it even more noticable..

Edited by SliverS2
The Mafia Grand Master

The Mafia

Posted
Posted

Oh no not a 5% rise in AFR's, how on earth are the exhaust valves going to survive that. Load is determined by the AFM, unless theres a leak or something else isnt working as it should then its fine to drive normally. Sure the AFR's arent always going to be EXACTLY the same as they were before but your not going to kill your motor by driving it around under light load. It takes AFR's upwards of 17-18:1 to do any damage to valves and pistons under light-medium load and you'd know all about it if it was that lean.

No worries. So you just take your nose out of your ass shove your nose up the exhaust and have a sniff, and go "Yep, shes safe enough, thats about 16:1"

My whole point - Unless you have a wideband you have NFI. So is it worth the risk.

I've also seen cars cruise fine at 17:1 without a miss. Wonder how those exhaust valves are doing.

Who knows. But nah, she'll be right hey. Just spent $6k on a turbo upgrade, its just money. Who gives a f**k about the engine.

Its ok though, my cars will always be safe. And the people that listen to my advice.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...