Jump to content
SAU Community

Recommended Posts

  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Spotted loads of 'lines out last night. Saw *Flick* twice doing anzac runs :devil: Don't know if you saw me going the other way.

Saw a very nice light blue 32 gts't going other way down Jetty road, kinda just stared at each other as we drove past each other..

Also a gun metal grey 32 GTR? following behind me as i drove towards Moana. Car sounded awsome as you were boosting behind me.

Spotted loads of 'lines out last night. Saw *Flick* twice doing anzac runs :devil: Don't know if you saw me going the other way.

Yeah i did see you, saw u heading city way? We wasnt doing anzac runs :blink: Was heading to matty t's for tea then going to meet few others for bit of a cruise.

Luke was probly driving, he pointed u out, we both commented on whether u were sau member or not.

Saw another blue 32 on anzac bout 1ish, like the darker ford blue colour, had maybe the same rims as mine. Never seen it before.

spotted dark bue 32 GTR down the bay tonite bout 7:30, possibly GTR-32^^ off here. Had p plates. Was a car or 2 behind the hot blue 34 i see around alot.

Also spotted Matty t's Ute down the bay bout 9:30 near the pool hall

spotted dark bue 32 GTR down the bay tonite bout 7:30, possibly GTR-32^^ off here. Had p plates. Was a car or 2 behind the hot blue 34 i see around alot.

Also spotted Matty t's Ute down the bay bout 9:30 near the pool hall

hehe, just got me that park too :D was around the place for a lil bit.............the damn thing wont die hahahaha

Yeah i did see you, saw u heading city way? We wasnt doing anzac runs :D Was heading to matty t's for tea then going to meet few others for bit of a cruise.

Luke was probly driving, he pointed u out, we both commented on whether u were sau member or not.

Saw another blue 32 on anzac bout 1ish, like the darker ford blue colour, had maybe the same rims as mine. Never seen it before.

Ahh ok. Yeh was heading to hj's on anzac h/w to have tea then was heading back down the bay and saw you heading city way.

spotted dark bue 32 GTR down the bay tonite bout 7:30, possibly GTR-32^^ off here. Had p plates. Was a car or 2 behind the hot blue 34 i see around alot.

Also spotted Matty t's Ute down the bay bout 9:30 near the pool hall

Yeh that was me also :( That 34's so nice. Love the kit on it. The blue looks wicked in the sun. Didnt see you tho, you wern't in the skyline?

Edited by GTR-32

Nah was in a white ford going the opposite direction.

Few out and about today, Black 32 up Brighton espy, and a red 32 that completely snubbed us off - 3 times! Black 33 with Veilside front and Gtr badge on brighton road.

just saw a 4 door silver 33 with black rims turning off nth east rd at the intersection where the cop shop is, looked clean.

Was also a white 33 2 door with kit and maybe rims sitting at the lights there too, didnt get a good look but.

And got a wave this arvo from a guy in a fairly stockish looking dark blue 32 while driving flicks car down brighton. She was passenger as usual lol.

edit: and rememebered another one from earlier, white 34, chrome rims, looked clean, exact location escapes me but think it was near city somewhere probly about 6ish.

Edited by skylineguy19
Spotted KACKLE tonight in Athelstone and Cara in her lovely 34 just a few minutes ago just passing the BP at the Golden Grove Village

hey dude wasnt me driving - it was regan by boyfriend going to pick his sister up from work! lol i was probably in bed by then cause ive had to get up at 5 the last few mornings :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...