Jump to content
SAU Community

Recommended Posts

Hi everyone,

Am looking at installing a double din DVD unit in my R34 GTR.

Mine came from factory with the TV unit - etc, so has the extra interior panels in the centre column (As per picture, sorry dony have a close up of the centre bit).

For those who have already done the conversion - do you have to source and replace the actual air con unit (as my current one seems a bit smaller than it does on my GTT and other GTR's).

Or is there a different larger facia which you can buy that snaps on to the existing unit?

Cheers in advance.

post-86021-0-35461200-1333809255_thumb.jpg

Edited by iwanta34gtr

The A/C Controls remain and should occupy the DIN slot just below the air vents.

The double-DIN head unit sits below that.

My former VS2 and Matt's current Nur have had the Alpine INA-W900E double-DIN head unit installed.

It's a superb unit with large screen GPS etc

One SAUer in WA was trying to sell his new unit below wholesale > F/S thread

The thin side strips have a brushed titanium look nearly identical to the standard R34 GT-R facia.

If you're not installing it yourself, Daniel of Carbon Car Systems Blacktown has been used by our family several times now Ph 1800.227.252

He does a lot for SAUers

Hi mate, thanks for the response as always.

Im familiar with the placement of the unit, however as I have the extra TV controls - etc in the centre of the dash, i could swear (unless my eyes are playing tricks with me) that the air con units facia appears a bit smaller than it usually would on the other examples without the TV controls?

if you are happy to lose the TV side of it then that unit can come out. the panels are different as well. the AC controls change. you need the non navi units. I can get them at a cost if required.

if you are happy to lose the TV side of it then that unit can come out. the panels are different as well. the AC controls change. you need the non navi units. I can get them at a cost if required.

you only get channel 7 and no picture anyway

if you are happy to lose the TV side of it then that unit can come out. the panels are different as well. the AC controls change. you need the non navi units. I can get them at a cost if required.

Hi mate, thanks for the reply.

I've taken another picture of my centre column to compare it to one without the extra nav unit above it.

The facia on the air con unit is slightly smaller than one without the nav unit, main question is whether the whole air con unit has to be changed for a new one, or whether there is another genuine nissan plastic facia which snaps on to the front of the air con unit to make it the same as the bigger one (as all the controls - etc look the same).

Cheers.

Mine -

post-86021-0-00999300-1333964380_thumb.jpg

Without the nav unit -

post-86021-0-50350400-1333964408_thumb.jpg

Edited by iwanta34gtr

nope they are different. you will need the 2DIN panel and the AC controls. from there its a plug and go affair.

if you need them new - shoot me a message.

  • 3 months later...

Chris, if the Nav unit isn't present is it possible to just insert a double din screen where the former radio and sunglasses compartment were or is the conversion kit required?

Hi mate,

If you already have the air con unit in the correct place, chances are the brackets you have in there can be reused.

Im assuming you have a single din unit with a pocket or similar underneath it. If you remove both, you can see if a double din unit fits in to the screw holes in your current brackets.

Hope this helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...