Jump to content
SAU Community

Recommended Posts

So currently putting a list together on what mods ile be doing to my 25, have a 8g budget im working with too achieve close too 400hp and build my 32 into a drifter, will never be rego'ed again.

currently im going with

definite mods

HyperGear G3 turbo

DW300 in-tank fuel pump

740cc Deatschwerks injectors

Maybe mods

EWP

6boost midmount

Greddy manifold

But im stuck deciding if i should go with E85 or a WMI setup, both have there pros and cons, for me E85 is harder too buy as im in queensland but the power gains and and anti det will be alot more then WMI, but WMI will bring my temps down, engine will run alot cleaner and is easy to get...or run 50/50 E85 and 98ron...hummm

any advice will be appreciated,

Thanks in advance!

Edited by 51NNA
Link to comment
https://www.sau.com.au/forums/topic/397600-wmi-or-e85-stuck-on-a-choice/
Share on other sites

you can easily run WMI on E85, but now your talking some serious power lol more than you will push from a G3

for a track dedicated car in a non E85 friendly area, WMI will be easier to make do with.

once E85 is easier to come by you wont be at too much of a loss to retune and on sell the WMI kit. The WMI kits are under $500 for something that will do the job.

Why is E85 hard to get for a track only car in brisbane? There's a caltex at goodna which sells it, you'd go past that on the way to QR. There's also one in ipswich itself, a few over on the bayside and one near mt gravatt.

WMI is a BC E85 or agrestic Oz [where E85 is unavailable] solution. If you have good access to E85 and never travel outside the metro area/s then use it - its cheaper and easier to set up than WMI. For all us erudites unable to take advantage of E85, WMI is the answer.

I think the question that determines which way you go is how often do you drive the car. A lot of k's will mean WMI.

I'd like to see someone try a little straight water with E85. You would spray 1/2 the volume that you would if using a WMI setup for the same power level. Around 400cc for 400kw atw.

The advantage I see is that you could run the E85 tune a lot leaner, into the 12.x:1 range. Which will help a little with fuel economy in the long run. I can't remember exactly, what he told me but Piggaz's car drinks E85 at a pretty alarming rate. Well over 10lt/minute at wide open throttle.

From what I understand about E85 tuning, rich AFR's under full load are needed to help keep detonation at bay and also to keep things from getting too hot. In this way E85 tunes more similar to pure methanol burning engines than ULP.

Im running a Microtech LT12s btw, its going to be a track car so distance isnt that much of an issue, you use around 45% more fuel when your on E85 because to get the same amount of energy from the fuel you require alot more, just like Avgas, i just dont want to have to bring 100LTs of E85 too every drift event lol

Can someone explain how you'd do the 50/50 ethanol mix, does this mean mixing fuel at home from a drum or would you have 2pumps at the servo, one for 98 and one for ethanol?

What kind of gains would you get from 50% mix if your making say 300kw with 98?

id say get 2 20lt drums and put both in your fuel tank, i wouldnt buy e85 from the pump, only the drums, i assume it would be simlar gains too straight E85 but not as much, would also require less fuel then straight E85

just go flex-fuel setup.

Ethanol content sensor

ECU with digital input (Link G4, some of the Haltechs etc)

And get some ID1000's at least, to leave you some headroom if you change your mind. Better injectors anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...