Jump to content
SAU Community

Recommended Posts

Well Scott's did 13.9 with more power. It's getting the barges off the line that counts. I have no doubt he would demolish mine in a roll on.

Hope you can stall it up with boost. Will be fast if you can.

Not likely, it wont even start. lol.

Luckily I got it going to get it off the dyno and onto the car trailer, when I got it home the damn thing was hydro-locked. Off with the heads next week for a check, if all's good I will replace the head gaskets, fit the ARP L19's and try again.

nice work guys, i was planning on running tomorrow but weather is shocking so ill have to wait till a day where its clear lets see waht stock power vs. now 300kw does

Yours will be a very interesting run mate, I wouldn't be surprised if you can get into the 12's with better tyres. Lighten it up as much as you can... :)

  • Replies 179
  • Created
  • Last Reply

Top Posters In This Topic

Best I could do was back up my 12.3,

Clutch didn't seem to like 300+kW+Drag launches+fat heavy car and is now rather f**ked.

I wont be buying another exedy clutch as it only lasted 9 drag launches and 10k km of fairly sensible street driving most of it on 280kW.

DVS JEZ what would you suggest? Car isn't driven daily and pedal weight is less of a concern but i would like to maintain some feel and not go back to the on/off switch HKS twin plate i had in it.

Edited by numleg

Sounds all to familair.....I have done 2 trips to the drags and done 2 clutches.....both were built by Race clutch

The 2nd one I killed actually had its last day on the street. It fused the carbonic clutch plate to the flywheel

and would not dis-engage. 4200lb single plate

I have just had a complete new clutch and billet flywheel installed. The factory flywheel was in bad shape with a blue heat ring around around the face where the linings ran. Clutch is a NPC this time. Will see how long it lasts...

The car is arount 1650kg

Trap speed was consistantly 185kph+ this should be good for a 12.00 or faster.

best 60 foot time was 1.8

This car won't see track time only street and drag. I have a 180 for track/drift/stupidshit.

I'm looking at what i can get local today otherwise i will order the nismo compermix comp $2200 from RHD Japan delivered isn't too bad but thats still a lot of cash.

My GTR runs an exedy cushion button twin plate. Even my missus can drive it. Has seen alot of abuse and circuit racing.

How much does ur car weigh?

Wht MPH did u run?

Edited by numleg

The car is arount 1650kg

Trap speed was consistantly 185kph+ this should be good for a 12.00 or faster.

best 60 foot time was 1.8

This car won't see track time only street and drag. I have a 180 for track/drift/stupidshit.

I'm looking at what i can get local today otherwise i will order the nismo compermix comp $2200 from RHD Japan delivered isn't too bad but thats still a lot of cash.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...