Jump to content
SAU Community

Recommended Posts

when im driving sometimes, no matter what gear im in, the turbo will spool but the engine wont go anywhere, then seconds later it will realise and continue like normal, i usually have to take my foot off the accelerator and put it back on for it to stop, so when im doing 50ks then go to 3rd, and acceletrate it wont go anywhere till i take my foot offf and put it back on.

any ideas?

Link to comment
https://www.sau.com.au/forums/topic/399470-a-flat-spot-in-r33-turbo/
Share on other sites

I was thinking it can't be that because it happens after I chuck it in gear and it happens if I just drive in the same gear and not change it...

These words still make it sound like its clutch slip. Where is the friction point on the clutch? High up the top?

ive since discovered, **sometimes** when i put my foot on the clutch as im coming to a stop the car will act like its conking out (engine light comes on, hicas comes on, revs go to 0) then when i take my foot off, the lights go away and the engine goes back to how it was? is that a transmission problem?

ive since discovered, **sometimes** when i put my foot on the clutch as im coming to a stop the car will act like its conking out (engine light comes on, hicas comes on, revs go to 0) then when i take my foot off, the lights go away and the engine goes back to how it was? is that a transmission problem?

Atmo BOV?

Does that happen in neutral or only when in gear?

If only in gear then the clutch is buggered and its not disengaging correctly

Need some more info. If u keep it in gear with the clutch in does it try and stall or only when u are slowing?

89cal may be right about the bov but need more info

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...