Jump to content
SAU Community

Recommended Posts

Hi

I am about to have a full exhaust system done on my series 2, RS Four S.

Not sure at this point wether to get twin dump pipe or just a bellmouth.

I will also be getting a Blitz LM return flow intercooler installed and was wondering if I will need to have the car tuned with aftermarket ecu piggyback or maybe Nistune board.

Or will the car run fine with the standard ecu ?

Any help would be great thanx

post-93563-0-21462800-1336787141_thumb.jpg

Since you have a S2 you would benefit from getting a Nistune fitted and tuned. The car will run on the stock ecu but from stock they all run very rich and a tune will benefit economy and/or performance and help your engine live longer.

Do the exhaust and the intercooler first if you want and get the Nistune as soon as you can.

Yes if you can source an R34 GT-t PFC and run 3.7v to pin 51 on the ecu to get around traction control you can use a PFC.

If you just gut your existing cat you get the same thing for free. More power noise very slightly increased.

nistune is about $350 without the software (off the top of my head)

+ cost of tune

pfc is $1000+

+cost of tune

with an exhaust and no tune on 7psi my rs4s was making 135awkw

10psi and a nistune + tune will get you near 200awkw

a guy i know with another rs4s said the tune was the most noticable mod he has done so far

also, the cost of tuning a nistune would only be a little more than a piggyback but you will get much better results

I already have Greddy power extreme exhaust, blitz intercooler, Greddy oil catch tank, JJR bellmouth dump pipe all awaiting to be installed. I will also be getting Splitfire coil pack and from what your all saying is I need Nistune board fitted, boost controller and then a tune. What kind of power should I then expect to see ?

Hey mate, perhaps jump into the Forced Induction performance thread and have a flick through the recent pages of the RB25 dyno results. That will give you something to go off, and then you can see what to expect. With the stock turbo, people don't push too hard.

Have you bothered to read anything in your own thread? I swear this has been asked and/or answered already more than once.

And right there is the reason a lot of people don't get on these forums cause there's always someone who has to show some infant ism.

I am merely asking to clarify so as not to get told some bs from a workshop. After all isn't that what this is here for. C'mon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...