Jump to content
SAU Community

Turbo Leak Blown Turbo? Rb25

Samhyland
 Share

Recommended Posts

Samhyland Enthusiast

Samhyland

Posted
Posted

Hi there I have a r33 skyline with rb25det running stock turbo with 160000kms. And I suddenly relised im getting no boost past vaccum what so ever goes up to 0 but no further? It also revs funny when turbo is meant to kick in and theres a strange smell? :/ anyone able to help? Thanks

Link to comment
https://www.sau.com.au/forums/topic/400206-turbo-leak-blown-turbo-rb25/
Share on other sites
hypergear Grand Master

hypergear

Posted
Posted

When the turbine wheels snaps the turbine pretty much stops spinning. and you will no longer get the turbo suction noise either. Pretty common issue for skylines. If you run high flowed turbo with stock boost it will be fine. how ever recommend to upgrade cooler exhaust and get a ecu remap to get the full potential from the high flow.

But having said that check to see if any cooler pipe's popped or any thing happened in that manner first.

chris_82 Enthusiast

chris_82

Posted
Posted

Even if the clutch was slipping, the turbo still would of produced boost if u were to rev it out of gear. As for the smell. when i give mine a bit of a hard time the exhaust smells like rotton eggs lol anyone else had this ?

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

Even if the clutch was slipping, the turbo still would of produced boost if u were to rev it out of gear. As for the smell. when i give mine a bit of a hard time the exhaust smells like rotton eggs lol anyone else had this ?

Haha my punched cat smells like shit now after a flogging

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...