Jump to content
SAU Community

Recommended Posts

Hey all,

So I was driving home on friday afternoon in the rain when suddenly I started to feel my rear shocks oscilations much much more than usually. I thought I may have punctured a tire from a pot hole or some other debris so I pulled over. Inspected my tires, all seemed fine. Checked my tire pressures, were a bit low so today (after not driving since friday) pumped them up to 40psi (235/R18s all round) and took her for a test. Problem still persists. Once home I did a shock bounce test and found them to still feel solid. (I have BC BR coil overs only about a year old). I have mine set relatively firm because of how low the car is with no guards rolled, keeps me from scrubbing ;) .

Anyhow, decided to jack the car up and down in the rear end to make sure the shockies were still expanding and retracting with and without load. All seemed normal. Now I'm a little stumped. I hadn't felt or heard anything break before I started feeling the excessive bounce. The BC BR Coilovers are less than a year (if not just comming up to a year) old so I wouldn't imagine they'd have seized or failed already.

I've got one theory (which I can't test until I get tools from the workshop tomorrow night) but perhaps if I back the firmness of the coils in the back off a little more, it may allow the shocks to absorb more of the shock rather than it being transfered to the wheels. I haven't seen any obvious bushes 'flogging' out when I had it last on the hoist either, that's not to say something hasn't happened spontaneously though.

So I am stumped for now. Any one else had this problem?

In Short:

Problem:

Boucy rear end

Fixes Tried:

- Tyre Pressures

- Inspectated Tyres (fronts are new and rears use to be the front so they still have tread)

- Suspension Bounce test

- Jacked up rear to inspect load and no load operation of coil overs

Yet to try:

- Softening up the rear coils via adjustable dampening dials.

Edited by Reflector

Um, you do realise that adjusting the dampers (softer) is not adjusting the springs, and will in fact make the suspension more bouncy?

Excessively hard damping will make the rear jittery and jumpy, which you may feel as being bouncy (or mis-describe as being bouncy). But bouncy is really when the springs are stiff and the loads are high enough to compress the springs but the dampers are not strong enough to control the oscillations of the springs after they get compressed.

To my knowledge the springs in the coils control/can be adjusted to vary the ride hieght which is adjust before being put into the car. I'm nearly certain that means that the actual spring itself does not vary in stiffness. The damping adjustment controls both rebound and compression - effectively what a shockie would do in a shock and spring style set up. I'm sure they'd have the information on the BC racing website.

Also lower your tyer pressure 40psi high and very hard. Try 34 psi. You may notice a difference also try some 17" rims as you will have more side wall to absorb the shock from the road

I used to have 19's I ran at 38psi no problems. Think the problem lies elsewhere

Also lower your tyer pressure 40psi high and very hard. Try 34 psi. You may notice a difference also try some 17" rims as you will have more side wall to absorb the shock from the road

34psi is too low for high profile tyres. Have always run 38-40psi in my 18" and never had a problem.

That being said, the problem seems to have gone away. After jacking the car up and releiving the coils of the load, my ride seems back to it's relatively firm state. Also was able to drive it through similar conditions (ie wet weather) and the same path on the weekend and there didn't seem to be a re-occurance of the problem. Perhaps the coils temporarily got stuck? Will be aware in any sudden change though if it happens again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...