Jump to content
SAU Community

Recommended Posts

Hey all,

So I was driving home on friday afternoon in the rain when suddenly I started to feel my rear shocks oscilations much much more than usually. I thought I may have punctured a tire from a pot hole or some other debris so I pulled over. Inspected my tires, all seemed fine. Checked my tire pressures, were a bit low so today (after not driving since friday) pumped them up to 40psi (235/R18s all round) and took her for a test. Problem still persists. Once home I did a shock bounce test and found them to still feel solid. (I have BC BR coil overs only about a year old). I have mine set relatively firm because of how low the car is with no guards rolled, keeps me from scrubbing ;) .

Anyhow, decided to jack the car up and down in the rear end to make sure the shockies were still expanding and retracting with and without load. All seemed normal. Now I'm a little stumped. I hadn't felt or heard anything break before I started feeling the excessive bounce. The BC BR Coilovers are less than a year (if not just comming up to a year) old so I wouldn't imagine they'd have seized or failed already.

I've got one theory (which I can't test until I get tools from the workshop tomorrow night) but perhaps if I back the firmness of the coils in the back off a little more, it may allow the shocks to absorb more of the shock rather than it being transfered to the wheels. I haven't seen any obvious bushes 'flogging' out when I had it last on the hoist either, that's not to say something hasn't happened spontaneously though.

So I am stumped for now. Any one else had this problem?

In Short:

Problem:

Boucy rear end

Fixes Tried:

- Tyre Pressures

- Inspectated Tyres (fronts are new and rears use to be the front so they still have tread)

- Suspension Bounce test

- Jacked up rear to inspect load and no load operation of coil overs

Yet to try:

- Softening up the rear coils via adjustable dampening dials.

Edited by Reflector

Um, you do realise that adjusting the dampers (softer) is not adjusting the springs, and will in fact make the suspension more bouncy?

Excessively hard damping will make the rear jittery and jumpy, which you may feel as being bouncy (or mis-describe as being bouncy). But bouncy is really when the springs are stiff and the loads are high enough to compress the springs but the dampers are not strong enough to control the oscillations of the springs after they get compressed.

To my knowledge the springs in the coils control/can be adjusted to vary the ride hieght which is adjust before being put into the car. I'm nearly certain that means that the actual spring itself does not vary in stiffness. The damping adjustment controls both rebound and compression - effectively what a shockie would do in a shock and spring style set up. I'm sure they'd have the information on the BC racing website.

Also lower your tyer pressure 40psi high and very hard. Try 34 psi. You may notice a difference also try some 17" rims as you will have more side wall to absorb the shock from the road

I used to have 19's I ran at 38psi no problems. Think the problem lies elsewhere

Also lower your tyer pressure 40psi high and very hard. Try 34 psi. You may notice a difference also try some 17" rims as you will have more side wall to absorb the shock from the road

34psi is too low for high profile tyres. Have always run 38-40psi in my 18" and never had a problem.

That being said, the problem seems to have gone away. After jacking the car up and releiving the coils of the load, my ride seems back to it's relatively firm state. Also was able to drive it through similar conditions (ie wet weather) and the same path on the weekend and there didn't seem to be a re-occurance of the problem. Perhaps the coils temporarily got stuck? Will be aware in any sudden change though if it happens again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...