Jump to content
SAU Community

Lost Car Keys - Advice Please

asitag
 Share

Recommended Posts

asitag Collaborator

asitag

Posted
Posted

Hey guys,

This is not related to my skyline, but the advice will probably be the same.

My wife has lost her keys to her '01 liberty (including spare key), and Subaru quoted $400+ for a replacement set.

Is there a way to get a locksmith to cut a new key set instead of spending such a ridiculous amount of cash to get a new set from the stealership?

We don't care about the immobiliser etc. Just need the stupid thing to start!

any advice?

Link to comment
https://www.sau.com.au/forums/topic/401210-lost-car-keys-advice-please/
Share on other sites
Nightcrawler Grand Master

Nightcrawler

Posted
Posted

^^ yeah right - if you read tip 6 of the article you linked to, most vehicles cannot have a new immobiliser fobs made (you need a dealer to do this) .... so have a tow truck ready - yeah right. So suddenly the $400 from the dealership seems cheap. They can probably make a new key and immobiliser fob from the VIN number of the vehicle, courier it to the OP and they are away.

And Kylie have you ever had the exact thing the OP is describing happen to you? Well I HAVE - so it seems you are the idiot giving out bad advice based on an American article you found on the internet. Useful. Not.

And I take it from your long history of warnings that your outspokenness has seen you undone before. So how about you stop talking about things you know nothing of.

If the OP followed your advice there is every chance that they would have to pay for a locksmith callout, non-genuine key to be made, unsuccessful non-genuine fob to be made, tow truck to the dealer, then the actual cost of the new key and fob. As I said above, this makes $400 seem very cheap.

Just go genuine. Yes stealerships suck, but to get a genuine key and fob and have 100% satisfaction the first time round, you would be foolish to call out a locksmith.

sonicii Veteran

sonicii

Posted
Posted

I agree with Nightcrawler. If you still had a working key, most good locksmiths can cut a new key and clone the immobiliser chip. But without a key or a chip, you are probably left with getting ripped of by the dealer.. assuming the liberty's have a chip in the key head..

Lucky it isn't a toyota.. some of them need to have the whole immobiliser system replaced if you don't have at least 1 working key on hand.

IMPORTD Grand Master

IMPORTD

Posted
Posted

err the op wasn't worried about the immobiliser for now, just a key, and if he calls around for pricing he most probably will save some coin but I guess that depends if he needs to tow his car or not.

The site offers advice and australian sites to visit. I didn't see anything to say it was American?

That statement about giving advice must have hit a nerve hey, but it was a general statement to anyone wanting to give advice. My advice was pretty clear, research your options. Don't just take someones 'word' for it.

You can hit below the belt and bring up private confidential information that shouldn't be aired on here....just shows how mature and professional you take your moderating position.

Vimana Enthusiast

Vimana

Posted
Posted

This car still has a transponder style immobiliser and will need a genuine key to start it. No locksmith can make a new key and code the transponder without the original. The best they will be able to do is unlock the door.

The reason it costs so much to do at the dealer is because the will need to fit a new body control module with matched key, not just code a new key.

I have a $15,000 scanner that can code most keys and do all OBDII stuff, but i cant code a new key unless i have the old.

Nightcrawler is correct in what he has said.

PS.... this is what i do for a living.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

This car still has a transponder style immobiliser and will need a genuine key to start it. No locksmith can make a new key and code the transponder without the original. The best they will be able to do is unlock the door.

The reason it costs so much to do at the dealer is because the will need to fit a new body control module with matched key, not just code a new key.

I have a $15,000 scanner that can code most keys and do all OBDII stuff, but i cant code a new key unless i have the old.

Nightcrawler is correct in what he has said.

PS.... this is what i do for a living.

and I agree. same thing goes with most of the newer cars. unless you have the pin code OR a working key dealer is the only way to do it. doesnt matter if you think its expensive or not.

VIM,

carmen or hannotech?

Alkatraz Rising Star

Alkatraz

Posted
Posted (edited)

I would be guessing that the keys for most manufacturers would simply come out of China and then be programmed by the dealers. Any chance of finding a blank for that particular model, having it sent to you and then going to the dealer to program it? The blank would probably cost $2 but based on the amount of time you would spend f'ing around doing this, it might be easier paying the $400.

Have a look at your home and contents policy (provided you have one), there might be a clause in there that covers something like this. Then just weigh up the $400 vs. your excess and possible premium increase on renewal. Some car insurance's will also cover this, the excess on the car insurance is generally higher though but may be worth a phone call to find out.

Edited by Alkatraz
Vimana Enthusiast

Vimana

Posted
Posted

and I agree. same thing goes with most of the newer cars. unless you have the pin code OR a working key dealer is the only way to do it. doesnt matter if you think its expensive or not.

VIM,

carmen or hannotech?

carmen.... i have the older one with the built in dual trace sillyscope and the newer touch screen blue one... sorry cant remember model names, but you get the idea. Also have all the european add ons.

sonicii Veteran

sonicii

Posted
Posted

The reason it costs so much to do at the dealer is because the will need to fit a new body control module with matched key, not just code a new key.

Is that true with subaru too? I am fairly sure a Nissan dealer can reprogram a new chip to NATS without needing an existing coded chip?? After all, when they enter the program mode, it erases all existing chips anyway.

sonicii Veteran

sonicii

Posted
Posted

I would be guessing that the keys for most manufacturers would simply come out of China and then be programmed by the dealers. Any chance of finding a blank for that particular model, having it sent to you and then going to the dealer to program it? The blank would probably cost $2 but based on the amount of time you would spend f'ing around doing this, it might be easier paying the $400.

Normally the keys are supplied with an existing unique code burnt into the chip, the car's immobiliser needs to be programmed to accept this code.

I purchased a chipped key for my J31 from hong kong, $25 for the key (free postage), about $10 to get it cut and $33 for nissan to program NATS to accept it. (which also cleared the old lost key) much cheaper than the $250+ that Nissan wanted to charge to do the same thing.

GTR-N1 Grand Master

GTR-N1

Posted
Posted

Hey guys,

This is not related to my skyline, but the advice will probably be the same.

My wife has lost her keys to her '01 liberty (including spare key), and Subaru quoted $400+ for a replacement set.

Is there a way to get a locksmith to cut a new key set instead of spending such a ridiculous amount of cash to get a new set from the stealership?

We don't care about the immobiliser etc. Just need the stupid thing to start!

any advice?

Has wifie lost other things besides 2-3 keys? I suspect so!

Short term memory? Cognition issues? PM me if she needs to have that tested.

Otherwise, if she thinks hypnosis might help her find at least one, as an SAUer, I'm happy to do it for mates rates (if I have a gap).

Thoughts?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V35_Paul
      Who has a Infiniti Q60, Q50 (V37)?

      By V35_Paul · Posted

      2 spots that my exhaust guy joined the 2 pipes together  Made a big difference. I'm now able to live with it. I can make it louder if I want by removing the HKS caps.
    • CefiroA31
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By CefiroA31 · Posted

      Hi all, considering clutch upgrade to support 1130 engine hp from 1650cc injectors on e50 at 85% duty cycle (1650 x (11.85/14.7) x 85%). Narrows down to these three as they can be converted to use gm 26 spline input shaft if I ever want to use transmission with that input shaft (orc1000f and r3c easy/cheap just change center hub; tr2cd pricier must change clutch discs). Pricing orc1000f similar to tr2cd, r3c about usd 200 pricier. Orc1000f triple plate 200mm. Tr2cd twin plate 215mm. R3c triple plate 215mm. Claimed max torque : orc 1000f 723 lbs ft; tr2cd 800 lbs ft; r3c 1100 lbs ft. Why orc1000f triple plate but claims lower max torque vs tr2cd twins? Is orc1000f underrated? Any info maxing out these clutches? Info on street/traffic driveability/pedal feel? Thank you for any info on them.
    • Dose Pipe Sutututu
      Yet another RB Neo misfiring thread after reading all the others.

      By Dose Pipe Sutututu · Posted

      Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • GTSBoy
      Yet another RB Neo misfiring thread after reading all the others.

      By GTSBoy · Posted

      Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
×
×
  • Create New...