Jump to content
SAU Community

Recommended Posts

  • Replies 247
  • Created
  • Last Reply

Top Posters In This Topic

Guys, I know it's a long shot but as posted in FB, anyone got a speed flow black -6 tool so I can fix my drama? I can still do skids without it but the AFRs are shit below half tank as I think the pickup hose and filter is stuck after messing around yesterday?

If you can't get a -6 wrench you should be able to use any adjustable wrench

Yeah didn't want to mark the fittings, however you just sparked an idea.... If I don't get it done tonight I'll get it done while im there....

Yeah didn't want to mark the fittings, however you just sparked an idea.... If I don't get it done tonight I'll get it done while im there....

oh, you poor thing.....

use an old tyre tube between shifter and fitting.

should work.

id say thered be a few, but yeah i got my 1400kg jack,

gotta jack one side at a time but come hit me up to use it, ill be in a red hoody and black jeans if you dont remember me from putty road cruise >.<!

id say thered be a few, but yeah i got my 1400kg jack,

gotta jack one side at a time but come hit me up to use it, ill be in a red hoody and black jeans if you dont remember me from putty road cruise >.<!

thanks man.

sorry, my memory is up to shite.

will remeet you tomorrow.

Manuel, I told you, call in sick.

they have to have someone to cover the shift.

what would happen if an emergency happened?

THIS IS AN EMERGENCY!

sounds good mate.

goodnight everyone, waking up at 4 tomorrow woo.

Bringing the second jack, we can do this shit NASCAR style!!!

Fking 4 am :( so not looking forward to that part, I'll hate you all until I wake up properly... Night :P

Being im only in doonside might sleep in till about 630am and still be there by 7. Only takes 10 min drive for me lol. Car is prepped and ready, helmet dusted all ready to go. Goodnight see u all soon!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...