Jump to content
SAU Community

Recommended Posts

What's wrong with auto?

I thought it was pretty rare to find a Tommy Kaira in Auto which is the only reason I mentioned the transmission type. I wasn't 100% sure if the TK R34 at wakefield was the same as the TK R34 shown in photos.

Edited by BakemonoRicer

f**k I'm pissed off now

Down in Sydney at the moment at a pub

Go out front to have a smoke and check the car and find some Kent has egged mine and got one one the car next to it as well

Only good

Thing is I bought a quick detailer kit with me so thanks to the bar staff for the buckets of water and got it washed off

Still pisses me off though that some pricks have no respect

f**k I'm pissed off now

Down in Sydney at the moment at a pub

Go out front to have a smoke and check the car and find some Kent has egged mine and got one one the car next to it as well

Only good

Thing is I bought a quick detailer kit with me so thanks to the bar staff for the buckets of water and got it washed off

Still pisses me off though that some pricks have no respect

Luckily you washed it off so quickly, egg is very corrosive and eats into the paintwork at a rapid rate.

When a car looks as immaculate as yours, it will attract good (admiration) and bad attention (jealousy). I'd be hesistant to take my car anywhere near a bar/pub, especially on a saturday night in Sydney. People become animals down there once some drugs/alcohol is in their system.

Edited by BakemonoRicer

f**k I'm pissed off now

Down in Sydney at the moment at a pub

Go out front to have a smoke and check the car and find some Kent has egged mine and got one one the car next to it as well

Only good

Thing is I bought a quick detailer kit with me so thanks to the bar staff for the buckets of water and got it washed off

Still pisses me off though that some pricks have no respect

thats crap mate, luckly you got to it quickly before it could do any harm. Still sucks though.

Edited by wedge_r34gtr

Thanks everyone

Hey how was lowdown

You still there?

What time you heading home?

Hey mate,

Ended up leaving the meet abit earlier as I had a mates party to get to back in newcastle, took off just after the presentation at about 5.

Was a very good turn out, Will post a few pics up later.

That's bs about the egg on your car mate.. I would have been fumming!

Finally home

I must have missed a spot in the dark on the spoiler cause when I checked cleaned the car in the morning some egg was still there and a few paint chips f**kin low life kent

Still a good day down Windsor for the fundraiser

Won't be taking the car next time though

Finally home

I must have missed a spot in the dark on the spoiler cause when I checked cleaned the car in the morning some egg was still there and a few paint chips f**kin low life kent

Still a good day down Windsor for the fundraiser

Won't be taking the car next time though

thats bad luck mate...

FYI have posted some lowdown pics in the wrap thread if you want to check them out.

http://www.skylinesaustralia.com/forums/topic/138419-nissan-paint-codes/page__st__0

Paint codes ^^^

1024571qs0.jpg

paint code on the one above is AH3 - i assume the number is in the same positon for GTT's

Also a useful link http://www.users.on.net/~goofyhsk/info/chassis_plate.html

For supply or to do the job?

Was going to tackle the job myself just need paints

EDIT Just made a thread in the paint section as well

Although now I think about it this a good excuse to do all the stuff I want at the one time

Edited by m.j.h

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...