Jump to content
SAU Community

Recommended Posts

Hi Gurus,

Sorry if this has been covered, but I have searched the interwebs and cannot find any answers.

I did a service on my R33 Series 2 about 3000kms ago with K&N oil filter and Motul 5w40 full synthetic.

I checked the oil level on the dip stick this morning and the oil was already on the low level. There are no leaks that i can see on the engine itself or under the car and i park the car in 2 same locations everyday so it would be visible if it was leaking from under the car.

What could this mean ? or is it normal for skylines to drink oil ?

I understand that its normal for old cars to drink oil but my r33 has only 123,000kms and full service logs and has been stock its whole life.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/
Share on other sites

On an oil change I always fill so that it ends up sitting on the high (hot) mark AFTER the car has fully recirculated the oil.

This means you can then very easily see if the oil were to drop for any reason during service intervals. Mine never does but if the day comes when i do ill know straight away.

Rb's also seem to be a bit safer with a higher oil level, especially if you give them some revs n cornering...

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6406612
Share on other sites

i would put 5 litres into it, not 4.3

bingo.

and just a random bit of trivia to make all us RB owners feel better about the amount of oil we need to feed our beasts. Particularly modified RB26's

- The Lamborghini Aventador needs 13 litres of what im sure is some pretty top of the line fully syn

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6406717
Share on other sites

I just rechecked it this morning and the level seems to be at the same level as when i filled it up(hasn't dropped). I also checked the radiator for oil and it seams to be clear.

I must have checked on a very slight angle, i have read somewhere that on a skyline even the slightest angle makes a huge difference to the reading.

Thx for all the replies.

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6407898
Share on other sites

sitting on the high (hot) mark

It's H for HIGH, not H for HOT.

If you replace the oil filter at the same time as you do an oil change, you need to put most of the oil in and run the engine for a few seconds before checking the oil level in the sump. Then add oil to bring the level up to the H mark.

Link to comment
https://www.sau.com.au/forums/topic/402890-drinking-oil/#findComment-6408183
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...