Jump to content
SAU Community

Recommended Posts

Well I got a call back toady after the pump assembly was tested and it's f@cked. The pressure switch and accumulator are shagged and the motor itself is chewed out with the impeller chewing on the inner casing all due to the pressure switch sticking on.

So I'm getting a change over reconditioned assembly ex Japan for $1920 to my door from Hills Motorsport. The new pump is the late updated model with a better pump design and Pre filters fitted. Only catch is its a 30 day wait from Japan then for Hills to bech check and set it up then post to me, I'm expecting to wait about 6 weeks until I can refit it. Still could have been worse as its the last ready unit on the shelf.

Edited by slippylotion

Well I got a call back toady after the pump assembly was tested and it's f@cked. The pressure switch and accumulator are shagged and the motor itself is chewed out with the impeller chewing on the inner casing all due to the pressure switch sticking on.

So I'm getting a change over reconditioned assembly ex Japan for $1920 to my door from Hills Motorsport. The new pump is the late updated model with a better pump design and Pre filters fitted. Only catch is its a 30 day wait from Japan then for Hills to bech check and set it up then post to me, I'm expecting to wait about 6 weeks until I can refit it. Still could have been worse as its the last ready unit on the shelf.

I might have a spare assembly soon, not sure on the condition yet. That sounds like an expensive rebuild to me...

I wouldn't say its expensive seeing as the accumulator is around $350 trade price alone and about $200 for a pressure switch that you can't actually buy from Nissan then the cost of a new pump that again you can't buy separate from Nissan and I need the complete assembly. Nissan only sell the complete pump assembly for $5k trade. New pump assembly in Japan is around 200,000yen from Nissan. These are rebuilt in Japan but with Australian warranty from Hills Motorsport. Im not keen to take the chance on a s/hand pump as it could go a week later. Atleast with this I have a warranty and shouldn't have any further problems for the 5 ish years Ill keep the car.

Im not keen to take the chance on a s/hand pump as it could go a week later. Atleast with this I have a warranty and shouldn't have any further problems for the 5 ish years Ill keep the car.

Yep, I agree it would usually be the best option but at that price? Its not like everyone else is replacing them, they are quite reliable in most cases. It's you coin buddy...

Yeah I agree its a lot of coin but it seems the cheapest way to fix it correctly and completely. I though of a second hand unit but they sell for $700-900 so if it dies in a year or two its really half the cost of the fully rebuilt assembly wasted seeing as a new unit should last another 10 years or so.

Id probably guess that the other guys getting the pressure switch fault code or 4WD randomly coming on are probably in the same boat. I asked why my torque gauge would still read if the pumps shagged and he said its a theoretical reading via the G sensor not the actual pump pressure. While the gauge is showing front drive it may well not be actually getting it.

$700-900 for 2nd hand? massive rip off

i have a complete unit here you can have for $150. no idea if/what is wrong with it. but it might be a hell of a lot cheaper to pull bits off than 2k for a 'new' one

Thats cheap. Theres one on Yahoo at 25000 yen so far then postage and fees it will be around $400-500.

I know $1900 seems like a lot but I don't want to have another problem with it again while I have the car. I suppose its similar to replacing a turbo with a cheap stock unit, bound to go at anytime so might as well just go a new one.

I also just double checked the oil I bled out of it last week while flushing some through and found all the little metal fillings in it. Just a bummer all 3 parts of my pump assembly died :angry:

Edited by slippylotion
  • 1 month later...

any more news on this one guys? i am wondering if my attessa has the same problem :( i have the same dashboard dimming and the front torque guage blip issue when the 4WD light is off.. when the 4WD light is on all is smooth.

though i think ill remove shafts and disable the pump rather than spend a heap of coin on fixing it..

nothing? :(

I had this issue...4WD light coming on intermittently, the ATTESSA pump chirping away...

I had a dead battery a month ago and replaced the battery, left the battery unplugged for a week.

Started driving again last Wed and haven't seen the 4WD light on yet...so not sure wtf the problem is...pump hasn't been chirping like mad either...

wow that sounds like a cheap fix :) maybe ill give it a shot this weekend :))

LOL you gonna disconnect the battery for a week?

TBH I think the problem will resurface after a few more weeks, maybe once the car is driven daily the strain on the ATTESSA system will probably cause it to come back...

awesome thanks Scotty will hit them up if import factory dont come through. what did they sting you for a read? can they translate the codes for you? and one last thing if the light doesnt happen to be on will they still be able to get it?

[END SPAM QUESTIONS]

:)

They only checked it, and told me the codes, they were in english and self explanatory as I remember. Give them a call and ask, tell them Scott sent you down.

The tcu doesn't show the codes with a malfunction lamp, that is for the engine only I think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...