Jump to content
SAU Community

Unigroup Engineering

Humbla

By Humbla,
in Engines & Forced Induction

 Share

Recommended Posts

Humbla Grand Master

Humbla

Posted
Posted

Well what can i say other than you boys are legends.My 33 has been running like crap for ages,now she is so much fun to drive.

Mark thank you for sorting out some probs,smoke machine is awesome.Yavuz thank you for tuneing my car 223.9 kw is a nice safe tune for my daily.Three boost settings wow,not too keen on low boost,but wow the higher 2 great fun.

You boys are the best will be back when i get a new muffler for another power run.I will totally recommend the unigroup team,they look after your car as if it was there own.Genelle. :D

Link to comment
https://www.sau.com.au/forums/topic/403741-unigroup-engineering/
Share on other sites
Humbla Grand Master

Humbla

Posted
  • Author
Posted

So what was the symptoms of ur issue and what was the fix

Mark did a smoke test and my gfb bov was leaking.He fixed it up.Yavuz fixed the pfc tune that was all over the place.All in all it only took 3 hours to tune where many others had tried to do but failed to do so.Lots of talkers out there,but really can't tune a pfc. :D

Humbla Grand Master

Humbla

Posted
  • Author
Posted

Big trip up for you Genelle. I'm surprised I didn't see your car out there.

Glad you got the result.

Awsome guys and out the effort in!

I am staying in bass hill at the moment,saw a 32r there with qld plates.Also a red 180 that i think belongs to liz. :happy:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Josh K.
      Crank Motorsports Front Axles

      By Josh K. · Posted

      Is anyone running these axles? R32, R33, R34 GTR front Axles. shafts itself rated 950hp. Suit all RB26 engines Croydon, Melbourne, Victoria Would be nice to pay half the cost of Driveshaft Shop Axles. I'm building an AWD S13 Coupe that is very low ride height (high cv angle) compared to stock R32. Has an RB30 with appx 600whp. Just looking for feedback. Thanks, Josh- https://www.instagram.com/feng_shui_garage/
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Been a long time since r31 got some love, my brother dropped a shitbox ls1 crapadore in my lap to fix up.  Put a wiper motor in as the flooded one was no longer alive.  got windscreen wipers now. Time to clean respray and install back in the titanic  IMG_0505.mov
    • PranK
      Returning after a long time!

      By PranK · Posted

      Nah its a server spammer thing  Although, now that I manually approve all the accounts I can probably loosen up some of the restrictions.  
    • CEF33Y
      Report that engine failure

      By CEF33Y · Posted

      Thread bump, again! Although, no bad news this time. Posting for the sake of possible root cause. Basically, I rebuilt it (mostly stock), installed Haltech + sensors, had it running fine on new ECU.  Still not really understanding why it cracked pistons last time. Got to tuners, and while checking timing, noticed +-10deg of timing scatter while revving. Changed CAS, and it was rock solid. While not definitive, can't imagine seeing 20+ psi with that amount of scatter would be a good thing. Also glad I found something.   Bit more of a run down; Carried out a stock rebuild, a set of stock pistons, out of a spare bottom end. Everything stock apart from head studs and oil restrictors. (so I can pretend I didn't let the Nissan out, ha.) Armed with the measuring gear and FSM, set about doing overhaul. Oil restrictors as per oil control thread for a RB25, stock oil pump, drifting. Head drain/vent from rear of head, to passenger side of sump above oil level. Two dash 10 vent lines from drivers side of sump (unused atm) Hi octane style cam cover breather kit Splash covers over last 2 cam caps. Both breather lines from cam covers to vented to atmosphere catch can, not plumbed back into sump (wanted to see what it was actually breathing). Got it run in (did about a 1000km) no to low boost scenario, As I had questions over old ECU setup. Installed haltech +sensors for flex Retune on E85 (finding CAS Issue along the way), made 300rwkw at 20psi, out of wastegate. Did a drift day the next day (yes, it was a big weekend!) and was checking catch can throughout the day, ZERO blowby. I mean nothing. Lines from cam covers are not even wet. Done a bunch of street driving, spirited and catch can is still dry. Early days I guess, but pretty happy so far. Also now run 10w60, up from the 10w40 that I used to run. Oil pressure is significantly better, especially when hot (as you would expect)      
    • GTSBoy
      Returning after a long time!

      By GTSBoy · Posted

      Done
×
×
  • Create New...