Jump to content
SAU Community

Noise From Cam Cover

R33ram

By R33ram,
in General Maintenance

 Share

Recommended Posts

R33ram Enthusiast

R33ram

Posted
Posted (edited)

hey guys just a quick question...

have this noise coming from my cam cover.

when its cold sounds a lil loud with revs around 1200/1300 rpm.

when i rev it goes away after 1600rpm and when idling at around 900/1000 can just hear it a little bit.

as it warms up it goes away at normal temp and goes away...

heres a video of it similar to mine or almost identical to be honest at the last 25 secs of video.

100% from the cam cover as i rember month ago tigtning those allen key bolts there and got extremly loud then loosend them and went away but its back again.

any ideas would be great or help on this as a few people have had this problem after reserching it but all different opinions...

Edited by R33ram
Link to comment
https://www.sau.com.au/forums/topic/404972-noise-from-cam-cover/
Share on other sites
Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted (edited)

Yea mine has been making this noise ever since the timing belt was done but i had a entire kit installed bearings belt everything changed professionally now it makes this noise on a cold start and goes away once it's warmed up...

What's the worst case scenario is it something that should be fixed asap or??

Edited by Lethal_aussie
R33 Eddy Proficient

R33 Eddy

Posted
Posted

Yea mine has been making this noise ever since the timing belt was done but i had a entire kit installed bearings belt everything changed professionally now it makes this noise on a cold start and goes away once it's warmed up...

What's the worst case scenario is it something that should be fixed asap or??

yours sounds like idler, if you are worried get the belt tension checked it could be too tight, if you installed a GATES belt and had it tension to stock spec it could be over tight.. worse case the idler gives way...

R33ram Enthusiast

R33ram

Posted
  • Author
Posted

yea get it checked tommorow but hate taking it to mechanics as they are always like what noise lol

Is there any damage to be done or is it just a noise that gets annoying and no affect to engine besides that?

I did put a bit of wd40 or it got in there and became louder lol so most likley the cause is what you saying....

Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted (edited)

yours sounds like idler, if you are worried get the belt tension checked it could be too tight, if you installed a GATES belt and had it tension to stock spec it could be over tight.. worse case the idler gives way...

Yep was a gate's racing belt kit, if the idler gives away what will happen lol? Just not crank over or will it actually damage the engine on failure? If its just a noise i wont worry about it ... Was all done professionally so its all under warranty etc ill just blast the mechanic and they can cop the bill.

Edited by Lethal_aussie
Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted

Yep was a gate's racing belt kit, if the idler gives away what will happen lol? Just not crank over or will it actually damage the engine on failure? If its just a noise i wont worry about it ... Was all done professionally so its all under warranty etc ill just blast the mechanic and they can cop the bill.

Besides the noise it does on idle on a cold start ... would it get much worse before that would happen or would it just suddenly happen? I had the entire gates kit done doesn't that include new idler's etc?? paid 400 bucks be damned if it was just the belt they replaced... regardless mechanic would be at fault anyways since they installed the kit and did the timing etc??

R33 Eddy Proficient

R33 Eddy

Posted
Posted

Besides the noise it does on idle on a cold start ... would it get much worse before that would happen or would it just suddenly happen? I had the entire gates kit done doesn't that include new idler's etc?? paid 400 bucks be damned if it was just the belt they replaced... regardless mechanic would be at fault anyways since they installed the kit and did the timing etc??

Did you supply the mechanic the parts or did they suggest the parts and source the parts? Warranty might not stand if you supplied the parts...

I installed the kit myself did the tension up and it was sweet, no noise or anything for a good year, recently i had to take the belt of and when i started the car it made that exact noise but much louder, i loosened the tensioner off and the noise has gone, im not worried that the belt will slip or jump and it was a Cu*t to even get off and back on again.

Next time i will just buy genuine Nissan belt as their is nothing is wrong with them..

Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted (edited)

Did you supply the mechanic the parts or did they suggest the parts and source the parts? Warranty might not stand if you supplied the parts...

I installed the kit myself did the tension up and it was sweet, no noise or anything for a good year, recently i had to take the belt of and when i started the car it made that exact noise but much louder, i loosened the tensioner off and the noise has gone, im not worried that the belt will slip or jump and it was a Cu*t to even get off and back on again.

Next time i will just buy genuine Nissan belt as their is nothing is wrong with them..

Yea im thinking that to should of got nissan ... im thinking its kinda overkill for street use gates... yea they sourced and recommended the gates timing belt kit they go through justjap i think.. as it was stronger etc

I always pay for a professional to install and source everything as im mechanically stupid in most area's lol... short of a oil change etc

Edited by Lethal_aussie
  • 4 weeks later...
Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted

yours sounds like idler, if you are worried get the belt tension checked it could be too tight, if you installed a GATES belt and had it tension to stock spec it could be over tight.. worse case the idler gives way...

*Just a update* on this guys, Had it checked again and the noise was the Timing belt which was actually loose.. and needed to be re-tensioned so all good now, cheer's :)

Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted

Hmmm

That is odd, how can the belt be loose?

I have exactly the same noise as you had, belt done months ago ..

Apparently the original mechanic that worked on my car was meant to re-tension the belt when i had the gates kit installed to begin with and didn't... The main mechanic "owner" said he had to redo the kit and tighten it as it was loose which is what was making the noise..

This is what i was told..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Hi guys, long time no post as per usual! It's been a busy year so far, the biggest thing being a new job.  After 28 years in the automotive industry I decided it was time for a change.  I was losing faith in the industry and where it's heading.  Now in a completely different industry (electrical) working for a company that manufacture water pump contollers.  Not as sexy as cars but it's an interesting,  challenging industry. I now don't work Saturdays which is a bonus!  It's still 50-55 hours a week but having Saturdays ack after 28 years of working them is awesome!   No news on the GT-R but i did decide to add some more JDM goodness into my life....           1990 300 ZX.  She's not perfect but for a 35 year old car she ain't bad!  Just going to tidy it up a bit and enjoy it.  It's currently auto but will start stockpiling everything for a manual swap. It WILL distract me even further from the GT-R but im hoping not for too long! It somewhat proves a 6'8" freak can fit in a 300 ZX.  Sort of...  I drove it home from the previous owners house in Melbourne via Black Spur and Merton Gap (2 awesome bits of Victorian twisty road) and it was amazing!  Handles so well!!!   I don't think it would be worthy of a full build page but I'll post up some of the upgrades here if anyone is interested?  Cheers guys!
    • shubby0901
      Living With An R33 Gtst

      By shubby0901 · Posted

      End game is to: - Remove all the slop from old worn parts - Adjust setup so that the wheels actually fit and the car is drivable (currently it is not because of the extreme rubbing on the guards).   Progress over the last couple of days, removed the rear hubs! Next steps: - Buy bushings - Replace bushings/bearings on hub - Reinstall
    • Hendasto
      Intro/R33 owner

      By Hendasto · Posted

      Hi, everyone!
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Cracked deck  And other cam snap stuff   
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      A few random issues have popped up since my last update. My WMI pressure sensor failed within about 10 minutes of it seeing liquid. It was a 20$ China special, so I'm not surprised. My name brand replacement should arrive today.  My power steering assist also decided to crap out last weekend. The usual, works for about 60 seconds after starting the car then I lose it. I dusted off my old copy of NDS and connected to the HICAS ECU. Code 4 for assist solenoid.... I tested the solenoid and it's fine.  I knew the day where my HICAS ecu would crap out would come, and I welcome it. It was the last HICAS part on the car that is now in the bin. I've ordered an SSR and I will control the power steering solenoid with my Haltech ecu. It will be nice to have proper speed referenced assist again after all these years.   
×
×
  • Create New...