Jump to content
SAU Community

Cross Threaded Spark Plug Hole

Plattsy

By Plattsy,
in General Maintenance

 Share

Recommended Posts

Plattsy Grand Master

Plattsy

Posted
Posted

Whats the best fix gents, geezer I know has a cross threaded spark plug which may be causing a miss fire, it's on the 6th cylinder so it's a pain int the arse to get too, but can this be tapped or re plugged?

Link to comment
https://www.sau.com.au/forums/topic/405141-cross-threaded-spark-plug-hole/
Share on other sites
Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

Just do what you did in europe then

tools are in Europe hence why he need's somewhere who can do it.............. and a generator is a little different to a skyline engine. if you feck the gen up nobody cares, i break his skyline he will cry!

anyone ever had it done by a mech?

to be honest even if i could borrow the tools i wouldn't feel confident.... we used to fill the hole with a rag forced into the top of the cylinder with the piston at tdc, once it was tapped we would vacuum out, remove the rag, vacuum again, then use a tiny fiber optic camera with a light to look for the fillings. it used to work. anyone confident enough to do this around the peninsula?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If you grease up the tap it should hold most of the chips in the flute, I'm guessing the thread only needs a cleanup anyway, as if the plug were fully cross threaded it would need to be removed and helicoiled.

A vacuum cleaner with a length of hose attached sounds like the go for cleaning out the bore, and those snake cameras are only $100 these days.

I doubt that is the cause of the missfire though...

533 RYC Proficient

533 RYC

Posted
Posted

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

it doesn't seem to bad. its at a very slight angle, towards the front of the engine, i say i think its misfiring but not actually sure car drives perfectly, but we changed the knackered coil packs, and the one on that spark plug was cracked, and it seemed like it was because of the angle it was attached.its not a major issue, but its just gonna cost a fair bit if it keeps cracking coils.

cheers for all the input fellas, we just really dont have the tools or equipment to do it ourselves. rather pay out 100 bucks or so rather than having to forkout for a new head/gasket/ancillarys etc.

Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

shame your in sydney boss, otherwise we would be round with some beer for ya in exchange!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • dawhitehonky
      M35 Aftermarket Fuel Pump

      By dawhitehonky · Posted

      I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • GTSBoy
      Rapid-fire squeaking/creaking from rear suspension

      By GTSBoy · Posted

      Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...