Jump to content
SAU Community

Neo Fuel Problem

JonnoHR31

By JonnoHR31,
in Engines & Forced Induction

 Share

Recommended Posts

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

Just finished putting an auto er34 rb25det into a manual hr31, wired it up and got it running yesterday. It started straight away and idles like a dream, except the ecu isn't putting in any extra fuel when pumping the throttle, making it UN-drivable.

I've been over the TPS wiring several times, its got power and at the ECU plug the signal wire reads .45v when closed and 4.0-4.1v at WOT so the ECU is getting the TPS signal and it's working as it should. As far as i know the TPS signal is the only thing the ECU uses for throttle pump injection so this has me stumped. Does anyone have any ideas why this wouldn't be working and how to fix it? Possibly something I've missed in the wiring? Or is there something else than can cause the same symptoms (stabbing the throttle causes revs to drop until the ECU picks up the extra flow via the AFM) that I'm missing?

Link to comment
https://www.sau.com.au/forums/topic/406040-neo-fuel-problem/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

You need to get a consult connection going so you can see what's going on.

You're also going to need to Nistune it if you want to be able to get around the lack of traction control and ABS that the ECU expects to see. Otherwise it will throw codes about the TCS/ABS comms and the TCS throttle position sensor.

JonnoHR31 Grand Master

JonnoHR31

Posted
  • Author
Posted

Consult isn't really possible at the moment unless I can find someone local with one, might have a scope around the WA section.

There was always going to be error codes but I was under the impression they wouldn't affect the actual running of the motor? I've taken it for a test drive and apart from this throttle hesitation it drives perfectly and doesn't have any cuts under full boost or anything.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Is it all still connected? If the ECU can't see the TCS TPS it'll have a fit.

The ECU still chucks a wobbly even if it is connected - if there is no TCS computer present to make the throttle do the close-open dance when the ignition is switched on. That's one of the error codes that comes up. Nistune can mask it.

And this stuff can still cause hassles even if you get past all these little annoyances. The Nistune blokes worked out that if you do not have the TCS stuff working, when you up the boost/flow and get up to a reasonably high power level, then the ECU starts pulling shenanigans that feels like a rev/boost limit, and can't be tuned out. It is possible that Stagea ECU images do not have that problem (as they do not use TCS).

GTSBoy Grand Master

GTSBoy

Posted
Posted

Got it sorted, had the ECU boost sensor hooked up to the manifold, moved it to the intake and now it's running fine. Weird.....

That'll do it. I just checked my engine. That sensor is connected to the crossover pipe immediately adjacent to the BOV. I guess it is not supposed to see vacuum.

Hanaldo Grand Master

Hanaldo

Posted
Posted

The ECU still chucks a wobbly even if it is connected - if there is no TCS computer present to make the throttle do the close-open dance when the ignition is switched on. That's one of the error codes that comes up. Nistune can mask it.

And this stuff can still cause hassles even if you get past all these little annoyances. The Nistune blokes worked out that if you do not have the TCS stuff working, when you up the boost/flow and get up to a reasonably high power level, then the ECU starts pulling shenanigans that feels like a rev/boost limit, and can't be tuned out. It is possible that Stagea ECU images do not have that problem (as they do not use TCS).

Spot on. It's very annoying :glare:

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

One of the wires was broken but it didn't make any difference.

Got it sorted, had the ECU boost sensor hooked up to the manifold, moved it to the intake and now it's running fine. Weird.....

Can u Please explain this a little more?

Had a 34 come in that had the same symptoms as urs after another mechanic did a headgasket. I had to disconnect the boost sensor to stop it trying to stall on takeoff. Such a simple little thing

JonnoHR31 Grand Master

JonnoHR31

Posted
  • Author
Posted

It seams to not like seeing vacuum, so just make sure it's hooked up somewhere before the T/B and it should be fine.

Thanks for the suggestions everyone.

Hi Jonno, i know its off topic but why did you get rid of your RB30DET and put a AUTO RB25DET neo into your HR31?

Sold the car to my younger brother, put a stocker neo (it's now manual) in for him and I'm selling my engine seperately along with a lot of other stuff.

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

It seams to not like seeing vacuum, so just make sure it's hooked up somewhere before the T/B and it should be fine.

Thanks for the suggestions everyone.

Sold the car to my younger brother, put a stocker neo (it's now manual) in for him and I'm selling my engine seperately along with a lot of other stuff.

ah cool . . . are you using the auto ECU that you got with the motor? could be causing issues if you are?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...